Stiga TITAN 540 D Instrucciones De Uso página 82

EN
1. Press the pedal forwards-
the machine starts to move for-
wards.
2. No load on the pedal – the
machine is stationary.
3. Pedal moved backwards –
the machine reverses.
4 The pedal is pressed towards neutral position
- the machine breaks.
In case of an emergency and the
machine does not brake as expected
when the pedal is reversed, the left
pedal (1:B6) should be used as an
emergency brake. NOTE! This puts
unnormal load on the parking brake
and shortens its service life.
3.4.2.6 Parking brake / Emergency brake (1:B6)
Never press the pedal while driving
except for in an emergency. Pressing the
pedal while driving reduces the service
life of the parking brake wich results in
a loss of functionality.
The pedal has the following
functions:
•When stopping. Parking
brake.
•During operation. Emergency
brake.
Indicator (1:I3) lights when the pedal is completely
depressed.
3.4.2.7 Inhibitor, parking brake (1:B7)
Never press the drive pedal (1:B5) when
parking brake is activated. This puts
unnormal load on the parking brake
and shortens its service life.
The inhibitor locks the pedal (1:B6) in the
depressed position. The function is used to
lock the machine on slopes, when trans-
porting, etc. when the engine is not run-
ning.
Locking:
1. Depress the pedal (1:B6) fully. The indicator
(1:I3) lights.
2. Press the inhibitor
3. Release the pedal.
Releasing:
1. Depress the pedal (1:B6) fully.
2. Release the pedal.
3.4.3 Controls – instrument panel
3.4.3.1 Throttle control (1:D1).
Control for setting the engine's revs.
Front position - Full throttle - when the machine
is in operation, full throttle should always be used.
Rear position - Idling.
82
ENGLISH
3.4.3.2 Ignition lock (1:D2)
The ignition lock is used for starting and stopping
the engine.
Four positions:
Preheat position: The cylinders are heat-
ed to facilitate starting. Hold in this posi-
tion as below at lower temperatures before
starting the engine.
Max 5 seconds
Stop position: The engine is stopped. The
key can be removed.
Operating position: Bypassed at start-up
and used when the engine is running.
Start position: The electric starter motor
is activated when the key is turned to the
spring-loaded starting position. Once the
engine has started, let the key return to the
operating position.
3.4.3.3 Implement lifter (1:Ls)
This control controls both the hydraulic tool lift at
the front of the machine (1:L) and the lift cylinder
for tools installed under the cab. These are con-
nected in series.
The control (1:Ls) only works when the engine is
running.
However, it can be lowered to the floating position
when the engine is off.
Never leave the machine with the imple-
ment in the transport position. Risk of
serious crushing injuries by the imple-
ment as it lowers quickly if the control
is unintentionally affected.
The lever has the four following positions:
Floating position. Move the lever to its
front position, where it locks. The imple-
ment is now lowered to its floating posi-
tion.
In the floating position, the implement
always rests against the ground at the
same pressure and can follow the con-
tours of the ground.
Use the floating position when carrying
out work.
Lowering. The implement lowers re-
gardless of its weight. The lowering
force is determined by the implement's
weight and the hydraulic down force that
is applied when lowering.
Locking in the transport position. The
lever has returned to the neutral position
after raising and lowering. The imple-
ment is locked in the transport position.
Original instructions for use