Stiga TITAN 540 D Instrucciones De Uso página 83

Raising. Move the lever to the rear posi-
tion until the implement is in the highest
position (transport position). Then re-
lease the lever to lock in the transport po-
sition.
3.4.3.4 Hydraulic control (1:Aux1s)
This control is used to control certain functions de-
pending on the attached implement.
The control only works when the engine is running
and the implement's hydraulic hoses for the in-
tended function are connected to the hydraulic out-
put (1:Aux1).
3.4.3.5 Hydraulic control (1:Aux2s)
This control is used to control certain functions de-
pending on the attached implement.
The control only works when the engine is running
and the implement's hydraulic hoses for the in-
tended function are connected as follows:
• Implement at the front via the hydraulic outputs
(1:Aux2f).
• 740: Implement at the rear via the hydraulic
output (1:Aux2r).
See also 3.4.3.9
Both hydraulic outputs on the rear section are con-
nected in parallel.
3.4.3.6 Switch (1:Os)
The switch can be used to smoothly set the
cutting height of the cutting deck with
electric cutting height adjustment.
The switch controls the contact (1O) with
switching polarity.
3.4.3.7 Switch (1:PTOs)
A lever for engaging and disengaging the opera-
tion of the front mounted implement. Two posi-
tions:
1. Press the front part of the switch – PTO
engages. The symbol will light up.
2. Press the rear part of the switch – PTO
disengages.
To prevent unnecessary increases in pressure in
the hydraulic system, set the throttle control to
1/4 throttle before the hydraulic PTO is en-
gaged.
The control activates a valve that transfers the
power from the hydraulic pump to the front mount-
ed implement.
The power is then transferred hydraulically to the
tool via the hydraulic output at the front (1:PTO).
3.4.3.8 Switch (1:Ts)
The switch has three positions and can be
12V
used for the sand spreader for example.
The switch controls the contact (1:T).
ENGLISH
3.4.3.9 Switch (1:Aux2fr) (740)
The switch has two positions and indicates
which hydraulic output will be activated
by the control (1:Aux2s). Front mounted
hydraulic output (1:Aux2f) or rear mounted hy-
dralic output (1:Aux2r). See also 3.4.3.5
3.4.4 Controls - other
3.4.4.1 Locking pins front (1:C1)
The machine has front and rear sockets for differ-
ent implements. The relevant implement is locked
by two locking pins after installation.
To secure the implement on the implement lift:
1. Insert the locking pin fully from the outside.
2. Place your foot on the locking pin and turn
backwards until it locks.
Do not turn the locking pin using your
hands. Risk of crushing injuries.
To release:
1. Turn the locking pin forwards until it unlocks.
2. Pull out the locking pin.
3.4.4.2 Locking pins rear(1:E1)
The machine has front and rear sockets for differ-
ent implements. The relevant implement is locked
by two locking pins after installation. The rear
locking pins self-lock in their grooves after instal-
lation.
3.4.4.3 Main switch (1:E2)
0
1
3.4.4.4 Engine casing
The machine may not be operated un-
less the engine casing is closed and
locked. Risk of burns and crushing in-
juries.
To access components on the engine, there are four
detachable covers. Open the covers as follows:
Cover on the right and left sides (1:K)
Removing:
1. Remove the front and rear rubber straps (1:J).
2. Pull the cover upward, fold it down and pull it
out.
Installing:
1. Lower the cover over the inside of the wheel.
2. Hook the cover's upper part into the machine's
V-groove and insert the locating pin at the bot-
tom.
3. Hook on the front and rear rubber straps.
Original instructions for use
Before carrying out work on the elec-
trical system, the power must be cut
using the main switch.
EN
83