Stiga TITAN 540 D Instrucciones De Uso página 88

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 139
EN
5.9 POWER ASSISTED STEERING
The power steering transfers the force from the
machine's hydraulic system to the steering wheel
when turned. This makes the machine very easy to
steer when the engine is running at full throttle.
Power steering forces reduce as the engine speed
reduces.
5.10 OPERATING TIPS
Always ensure that the correct amount of oil is in
the engine. Especially when driving on slopes.
See 5.3.
Be careful when driving on slopes. No
sudden starting or stopping when
moving up or down a slope. Never drive
across a slope. Move from the top down,
or from the bottom to the top.
The machine must not be driven in any
direction on slopes with a gradient
greater than 10º.
Reduce the speed on slopes and when
making sharp turns to prevent the
machine from tipping over or you
losing control.
Do not turn the steering wheel to full
lock when driving in top gear and at full
throttle. The machine can easily topple
over.
Keep hands and fingers well away from
the articulated steering joint and seat
bracket. Risk of crushing injuries.
Never drive with the engine casing
open.
Depending on the implement used,
counter weights might have to be
mounted on the machine. The axle
pressure of a wheel axle may never
exceed 900 kg or 70% of the total
weight of the machine
5.11 STOP
Disengage PTO. Apply the parking brake.
Allow the engine to idle 1 - 2 mins. Stop the engine
by turning off the starter key.
If the machine is left unattended,
remove the ignition key.
The engine may be very hot
immediately after it is shut off. Do not
touch the silencer or other engine parts.
This can cause burn injuries.
5.12 BLEEDING THE FUEL SYSTEM
(540)
If there is air in the fuel system, this must be bled
manually. Air may have entered due to the follow-
ing:
• After stopping due to lack of fuel.
88
ENGLISH
• After replacing the filter.
• After draining the water separator.
• After carrying out repairs in the fuel system.
Never attempt to carry out bleeding by
turning the engine with the starter
motor. This will damage the starter
motor.
Bleed as follows:
1. Check that the fuel tank is filled.
2. Open all taps in the fuel system.
3. Pump using the control (5:J) until all air has
been pumped out of the fuel system.
4. Attempt to start. If the engine does not start,
continue bleeding as above.
5.13 CLEANING
To reduce the risk of fire, keep the
engine, silencer, battery and fuel tank
free from grass, leaves and oil.
To reduce the risk of fire, regularly
check the machine for oil and/or fuel
leakage.
Never use high-pressure water. This can
damage shaft seals, electrical
components or hydraulic valves.
Never use high-pressure air against the
radiator fins. This will damage the fin
structure.
Clean the machine after use. The following in-
structions apply to cleaning:
• Do not point jets of water directly at the engine.
• Clean the engine with a brush and/or com-
pressed air.
• Clean the engine's radiator (10:R) with a soft
brush. Large objects can be removed by hand.
If the coolers are heavily soiled, clean using
slow running water and a suitable detergent.
• After cleaning with water, start the machine and
any cutting deck to remove the water that may
otherwise penetrate bearings and cause damage.
6.1 SERVICE PROGRAM
In order to keep the machine in good condition, as
regards reliability and operational safety as well as
from an environmental perspective, the service in-
structions in this section should be followed.
All services should be carried out by authorised
workshops.
Service, carried out by authorised workshops,
guarantees a professional job with original re-
placement parts.
The service log should be stamped at every service
carried out by an authorised workshop. A "fully
Original instructions for use
6 MAINTENANCE

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Titan 740 d

Tabla de contenido