Connecting The Audio Components - Marantz SR-12S1 Manual Del Usuario

CONNECTING THE AUDIO COMPONENTS

MD PLAYER
DIGITAL
INPUT
The output audio signal from the TAPE OUT jack and the CD-R/MD
OUT jack is the sound source currently selected.
Caution:
• Do not connect this unit and other components to mains power
until all connections between components have been
completed.
Notes:
• Insert all plugs and connectors securely. Incomplete
connections may make noise.
• Be sure to connect the left and right channels properly.
Red connectors are for the R (right) channel, and white
connectors are for the L (left) channel.
• Be sure to connect input and output properly.
• Refer to the instructions for each component that is connected
with this unit.
• Do not bind audio/video connection cables with power cords
and speaker cables will result in generating hum or other noise.
CONNECTING DIGITAL AUDIO COMPONENTS
• There are 9 digital inputs, 5 coaxial jacks and 4 optical jacks, on the
rear panel. You can use these jacks to input PCM, Dolby Digital and
DTS bitstream signals from a CD, DVD, or other digital source
components.
• There are one digital output with coaxial jack and one with optical
jack on the rear panel. These jacks can be connected to CD
recorder, MD deck.
• Setup the digital audio format of DVD player, or other digital source
component. Refer to the instructions for each component to be
connected to digital input jacks.
• Use fiber optical cables (optical) for DIG-1, 2, 3, 4 input jacks. Use
75 ohms coaxial cables (for digital audio or video) for DIG-5, 6, 7, 8,
9 input jacks.
• You can designate the input for each digital input/output jacks
according to your component. See page 32.
OUT
L
R
SACD PLAYER
L R
R L
DIGITAL-OUT
OPT
PRE OUT MAIN IN
GND
1
L
ANTENNA
2
R
COAX
GND
MODEL NO.SR-12S1
3
C
AM
4
RS232C
SW
R L
5
FRONT
CD
SL (AUX 2)
EXT. IR
OUT
6 IN
SURR.
SR
DC OUT 1 DC OUT 2
TAPE
SURR.
7
OUT
BACK
SBL
IN OUT
MULTI IN
SBR
RC 8
CD-R
SUB WOOFER CENTER
/MD
MULTI
OUT
9
RC-5 OUT
DIGITAL-IN R L 7.1CH-INPUT R
R L
R L
OUT IN
DIGITAL DIGITAL
OUTPUT INPUT L
R
OUT
L
R
CD PLAYER
L R
R L R L R L
MONI.
2
MULTI VIDEO MONI.
Y
1
OUT
MONITOR
LD CB
OUT
DVD
CR
DSS Y
VCR2 /
DSS
DVD - R
IN
IN
TV CB
IN CR
VCR1
Y
OUT
DVD VCR1
IN IN
IN CB
VCR2/
DVD-R
CR
OUT
AUDIO L R L VIDEO S-VIDEO COMPONENT VIDEO
R L
L R
L
R
CD RECORDER
Notes:
• There is no Dolby Digital RF input jack. Please use an external
RF demodulator Dolby Digital decoder when connecting the
Dolby Digital RF output jack of the video disc player to the
digital input jack.
• The digital signal jacks on this unit conform to the EIA
standard. If you use a cable that does not conform to this
standard, this unit may not function properly.
• Each type of audio jack works independently. Signals input
through the digital and analog jacks are output through the
corresponding digital and analog jacks, respectively.
OUT IN
L L
R R
TAPE DECK
L R
L R
– + – +
FRONT MULTI
ROOM
LEFT
LEFT
FRONT MULTI
ROOM
RIGHT
RIGHT
SURR.
CENTER
BACK
LEFT
SURR. SURR.
BACK LEFT
RIGHT
SURR.
SPEAKER SYSTEMS
RIGHT
6-8 OHMS
AC IN
25