Preference; Surround - Marantz SR-12S1 Manual Del Usuario

PREFERENCE

3 P R E F E R E N C E
T V - AU T O
OS D I N F O
D I G I T A L OU T
S U BWOOF E R OU T
MA I N
1.
Select "PREFERENCE" in MAIN SETUP MENU with Up or
Down cursor button, and press the OK button.
2.
To select a desired content, press Up or Down cursor button.
TV AUTO: Select the TV AUTO ON/OFF function to enable or
disable with Left or Right cursor button.
(refer to page 44)
OSD Info: Select the OSD information function to enable or
disable with Left or Right cursor button.
If you select "ENABLE", SR-12S1 will display the
status of the feature (Volume up/down, input select,
etc..) on the TV monitor. But if you do not desire this
information, select "DISABLE ".
DIG. OUT: Select the digital source to output the DIGITAL OUT
terminals with Left or Right cursor button.
This is for digital dubbing to a CD-R recorder or MD
deck. (See page 45)
The source is switched in the following sequence.
SOURCE → DIG.1 → DIG.2 → → → DIG.8 → DIG.9 →
AUX → OFF → SOURCE →
SUB-W OUT: "THX" position is required, but If you desire an
additional front L/R mixed subwoofer output in the
STEREO mode, select "L/R MIX" with Left or Right
button.
If you finish the setup in this item, move cursor to "MAIN" with Up or
Down cursor buttons and press OK button.
: D I S AB L E
: E NAB L E
: SOURC E
: T H X
E X I T

SURROUND

4 S URROUND
S URR . MOD E
C I N EMA R E - EQ
L F E L E V E L
S URR L / R E F F E C T
S URR B ACK E F F E C T
C E N T ER E F F E C T
S UB W E F F E C T
MA I N
1.
Select "SURROUND" in MAIN SETUP MENU with Up or Down
cursor button, and press the OK button.
2.
To select a desired content , press Up or Down cursor button.
SURR-MODE : Select the desired surround mode with Left or
Right cursor button.
CINEMA RE-EQ™ : Select to active the Cinema Re-EQ™ with Left
or Right cursor button.
The tonal balance of a film soundtrack will be
excessively bright and harsh when played back
over audio equipment in the home. This is
because film soundtracks were designed to be
played back in large movie theater environments.
Activating the Cinema Re-EQ™ feature when
watching a film made for movie theaters corrects
this and restores the correct tonal balance.
Cinema Re-EQ™ is therefore not necessary for
material that was not designed for movie
theaters (for example, sports programming,
television shows, made for TV movies, etc..).
The Cinema Re-EQ™ feature can be activated
only while in Dolby Pro Logic Mode, or while
decoding Dolby Digital or DTS encoded
material.
LFE LEVEL : Select the output level of the LFE signal included
in the Dolby Digital signal or the DTS signal.
Select 0 dB, -10 dB or OFF with Left or Right
cursor button.
The level is ordinarily set to 0 dB except DTS-
Music mode. In the DTS-Music mode, default
level is set to -10 dB.
EFFECT LEVEL
SURR L/R EFFECT: Set the effect level of the Surround speaker
between –3 and +3 level in 1 level interval .
• If "None" was selected for the Surround speakers setting in the
Speaker size, then this setting will not appear.
SURR BACK EFFECT : Set the effect level of the Surround Back
speaker between –3 and +3 level in 1 level
interval .
• If "None" was selected for the Surround back speakers setting
in the Speaker size, then this setting will not appear.
CENTER EFFECT : Set the effect level of the center speaker between
–3 and +3 level in 1 level interval .
• If "None" was selected for the Center speaker setting in the
Speaker size, then this setting will not appear.
SUB W EFFECT : Set the effect level of the subwoofer speaker
between –3 and +3 level in 1 level interval .
• If "None" was selected for the Subwoofer speaker setting in the
Speaker size, then this setting will not appear.
Note:
• These effect level set up are available only while in HALL,
MATRIX, MOVIE, CSII, Multi CH. STEREO.
If you finish the setup in this item, move cursor to "MAIN" with Up or
Down cursor buttons and press OK button.
: AU T O
: O F F
: 0 d B
: ∗ ∗ ∗ d B
: ∗ ∗ ∗ d B
: ∗ ∗ ∗ d B
: ∗ ∗ ∗ d B
E X I T
35