General Characteristics - CAME Z Serie Manual De Instrucciones

ENGLISH ENGLISH ENGLISH
ENGLISH ENGLISH
Description of control panel
Control panel for 24 VDC gear motors,
powered by 230 VAC at 50-60 Hz (single-
phase).
Designed to control ATI/FROG/FERNI or
FLEX gear motors, with or without encoder,
in systems employing 1 or 2 gear motors.
Designed and built entirely by CAME to
meet UNI 8612 safety standards at an IP
54 level of protection. Housing in ABS is
equipped with vents to provide internal air
circulation. Guaranteed 12 months, unless
tampered with.
This control panel is powered by 230V AC
across terminals L1 and L2, and is
protected by a 1.6 A fuse on the main
power line as well as by a variator. The
total power consumption of 24 V
accessories (which are protected by a 1.6
A fuse) must not exceed 40 W.
Safety
The basic safety system consists of an
amperometric detector on the control
panel. This system immediately stops gate
movement if an obstacle is detected during
the opening cycle, and re-opens the gate if
an obstacle is detected during closing. The
sensitivity of this detector is adjustable:
the amperometric reference values, which
are determined during the self-test cycle
(see dip switch 10), can be increased by
20% or decreased (slowdown cycle, only)
by 15% if necessary.
Photocells can be connected to obtain:
- Re-opening during the closing cycle;
- Re-closing during the opening cycle;
- Temporary stop (shutdown of movement if
obstacle is detected, with resumption of
movement when obstacle is removed);
- Partial stop (shutdown of moving gate,
with activation of an automatic closing
cycle);
- Total stop (shutdown of gate movement
without automatic closing; a pushbutton or
radio remote control must be actuated to
resume movement).
Accessories which can be connected
- "Gate open" signal light;
- Light with courtesy function (lights up for
a fixed period of 120") or cycle function
(lights up during the entire opening/closing
cycle);
- Flashing signal light when gate is in

GENERAL CHARACTERISTICS

motion;
- Electric lock;
- LB18 circuit card for emergency battery,
which is automatically connected in case of
power failure; battery is recharged when
line power is restored;
- Plug-in radio receiver.
Other functions
-Automatic closing: The automatic closing
timer is automatically activated at the end
of the opening cycle. The preset,
adjustable automatic closing time is
automatically interrupted by the activation
of any safety system, and is deactivated
after a STOP command or in case of power
failure;
- A "hammer movement" can be applied to
the gate to facilitate release of the electric
lock;
- Detection of obstacle when motor is at
the end of its travel (gate completely open
or closed);
- Opening to allow pedestrian travel
(opening performed by motor M2, only).
Can be total or partial;
- "Operator present" function. Gate
operates only when the pushbutton is held
down;
- Flashing light activated before opening
and closing cycle begins;
- Type of command:
-open-close-reverse by button and trans-
mitter;
-open-stop-close-stop by button and trans-
mitter;
-open only by transmitter.
Adjustments
- Trimmer VEL = Operating speed: min/
max;
- Trimmer RALL = Slowdown speed: min/
max;
- Trimmer SENS = Sensitivity of
amperometric safety system: min/max;
- Trimmer TCA = Automatic closing time: 1"
to 180";
- Trimmer TL = Operating time: 10" to 110";
- Trimmer AP PARZ. = Partial opening time:
1" to 26";
- Trimmer TR2M = Delay on closing cycle -
motor 2: 1.5" to 17";
the main power lines before carrying out
any operation inside the unit.
Important! Disconnect the unit from
-3-