Measuring Procedure; How To Use The Memory Function; To Delete All Values Stored In The Memory; Maintenance And Repairs - Medel Elite Manual Del Usuario

EN

4.3 Measuring procedure

After the cuff has been appropriately positioned, the measurement can begin
1. Press O/I button. All display symbols appear for 1 second. Then 0 will appear
on LCD on the DIA column. (pic. 10). The monitor is ready for the measurement.
2. Then the cuff inflates automatically. The symbol " " will appear. (pic. 10)
3. Once a pulse is detected, the "
4. When appropriate pressure is reached, inflation stops and the cuff starts to deflate.
5. When the measurement is completed, the systolic / diastolic pressure and pulse are
shown simultaneously .
6. In case the measurement shows irregular heartbeat (I.H.B.), the "
displayed. In this case the results of the measurement have deviated from a normal
situation. Then the measurement needs to be repeated. In the majority of cases, this
is not cause for concern. If the symbol "
times a week during different daily measurements) it is advisable to discuss it with
your medical advisor (pic. 12).

4.4 How to use the memory function:

• In clock mode (Off mode), press MEM button. The number of stored data is shown
(Pic.14), sudden the latest result will be displayed with date and time (Pic.15)
• Press MEM button repeatedly to review the results measured.
4.5 T3 System: How to see the average of the last 3 measurements (taken within the
last 15 minutes)
1. Press O/I button and take the first measurement.
2. At the end of the first measurement wait at least 5 minutes in a relaxed position.
Then repeat the measurement following step 1 again.
3. At the end of the second measurement wait at least 5 minutes in a relaxed position.
Then repeat the measurement following step 1 again.
4. At the end of the third measurement press T3 button to perform the average of the
last three measurements taken (the AVG symbol will appear) (pic. 16).
NOTE:
The average data using T3 button is shown only if the last 3 measurements have been
done within 15 minutes. Otherwise, the data will be shown as 0.

4.6 To delete all values stored in the memory

In Clock mode (Off mode) press MEM button, after the latest data stored will be
displayed press again and hold the MEM button for 3 sec. All results will be deleted.
Press the MEM or O/I button to turn off the display (pic. 17).
5. ERROR MESSAGE/MALFUNCTION
Follow the below recommended actions and press O/I button again to start another
measurement.
Error code Possible cause(s)
E1 Deflation is too fast or the cuff
doesn't inflate
E2
The cuff is very tight
E3
The cuff pressure is excessive
33
100114_MEDEL ELITE USER MANUAL_REV.00_FEB.2017.indd 33-34
"symbol blinks. (pic. 11)
"symbol is
" appears regularly (for example several
Recommended actions
Re-apply the cuff and try again
Relax for a moment and try again
E10
The monitor has detected mo-
vement during reading
E11
E20 The reading process cannot
detect the heart beat
E21 Inaccurate reading
E Exx There is a calibrationa pro-
blem
Out Out of measurement range
5.1 Other possible malfunctions:
Problem Possible cause(s)
The display shows the Batteries are drained.
symbol
The blood pressure The cuff is not wrapped cor-
values displayed are rectly or not at the level of the
abnormally high or heart.
low.
Too much stress is applied on
your shoulder or arm.
You move your arm or arm
muscles during measurement.
The (I.H.B.) symbol You move your arm or arm
" " is displayed, muscles during measurement.
but my heart beat rate
should be normal.
The light on the di- The batteries are flat or not
splay is dim or not lit right placed.

6. MAINTENANCE AND REPAIRS

For any repair operations, only refer to a technical assistance centre authorized by
the Medel International Srl and request original spare parts. Never open the device.
There are no user-serviceable parts within. The device requires no lubrication or main-
tenance. Failure to comply with what expressed above may compromise the safety of
EN
Movement could compromise the reading.
Relax for a moment and try again.
Movement can compromise the measure-
ment. Relax for a moment and try again .
Loosen the clothes on the arm and try again
Relax for a moment and try again
Repeat the reading. If the problem persists,
contact the Service Centre. Refer to the war-
ranty for the contact information and the
instructions concerning returns.
Relax for a moment. Refasten the cuff and
then measure again. If the problem persists,
contact your physician.
Recommended actions
Replace all batteries with new ones.
Wrap the cuff correctly and rise your
hand so that the cuff is at the same
level of your heart.
Relax yourself and make measure-
ment.
Remain still and do not move /contract
the muscles during measurement.
Remain still and do not move /contract
the muscles during measurement.
Replace the flat batteries with new
ones. Insert the batteries correctly.
34
10/02/2017 19:02:59