Information On Domina Series Gas Fryers; Laws, Regulations And Technical Directives To Be Observed; Place Of Installation; Positioning - MORGAN Catering Equipment Somina Serie Instrucciones Para La Instalación, El Uso Y El Mantenimiento

2.1

INFORMATION ON DOMINA SERIES GAS FRYERS

This booklet applies to our Domina series Fryers type A Category II (Natural Gas and L.P.G.). See table 1.1 - 2.5. The plate
according to EN 437 and EN 203 part 1
standards is under the bottom edge of the
instrument panel.
2.2 LAWS, REGULATIONS AND
TECHNICAL DIRECTIVES
TO BE OBSERVED
The following regulations must be observed
during installation:
- Current accident and fire regulations.
- The regulations of the gas supply
company, which has to issue an
authorization before installation.
- "Gas system installation" standards.
- Health regulations.
2.3

PLACE OF INSTALLATION

- The unit should be installed in a room with adequate ventilation. This unit requires a draft of at least 2 m
(Thermal Capacity).
- Install the unit in compliance with the safety regulations UNI - CIG 8723, Italian Law No. 46 dated 5-3-'90 and Ministerial
Decree No. 74 dated 12.04.96.
2.4

POSITIONING

- The various units may be installed separately or combined with other units in our range.
- This unit is not suitable for encasing.
- The distance from the side and rear walls must be at least 10 cm.; should the distance be less or the material of the walls or
floor be flammable, it is vital to install heat insulation.
2.5 TABLE II: GAS TECHNICAL DATA, PRESSURE, BURNER NOZZLES, PILOT AND MINIMUM SCREW.

UNIT TYPE: GF49T AND GF99T WITH BASIN OF 18 LITRES

Nation Cat. Type
and NOZZLE of
category gas
ENG, ICEL,
DENIM, FIN,
SWED, PORT, 2H G20
GREECE,
IRELAND
NETHERLANDS 2L G25
ICEL,
DENMARK, 3B/P G30*
FINLAND, G31
SWEDEND
IRELAND
PORTUGAL 3+ G30*
ENGLAND G31
GREECE
NORWAY 3P G31
LUXEMBURG 3P G31
LUXEMBURG 3P G31
NETHERLAND
R.o.A. = Regulation of primary air
* Pressure regulator excluded
GB
All manuals and user guides at all-guides.com
V
IT-GR-GB-ES-IE
II2H3+
Cat.
P n 20,29/37
LU
Cat. II2E3P
P n 20,37,50
Qn
(Hi)
Gas pressure
N° 3 BURNERS
upstream
mbar
Ø mm. Type R.d.A.
Nom. Min. Max.
MARKED X mm.
20 17 25 165/250 K 32
25 20 30 170/350 L 28
29 25 35 115/250 K TA
29 20 35 115/250 K TA
37 25 45
30 20 35 120 K TA
37 25 45 115/250 K TA
50 42,5 57,5 105/250 K TA
(1) Including the pilot thermal capacity approx. 400W.
K = Short nozzle l = 15 mm
Mod.
Matr.N°
Hz
PT FR-BE
II2H3+ II2E+3+
20,29/37 20/25,29/37
IS-DK-FI-SE AT-CH
II2H3B/P II2H3B/P
20,29 20,50
3
G20 m /h
kW
3
G25 m /h
BY-PASS PILOT Gas pressure at
nozzle
with 710
Ø mm. "targhet" Max.
MARKED MARKED mbar mbar
- 36 18,5
- 36 23,2
- 19 28,4
- 19 28,4
36,9
- 19 29,3
- 19 36,8
- 19 49,2
F = Fixed A = Adjustable
- 14 -
Type
kW
tipo
NL
II2L3P mbar
mbar
25,30,50
DE NO
II2ELL3B/P I3P
20,20,50 30
G30 Kg/h
G31 Kg/h
3
/h • kW T.C.
Nominal Gas consumption
Thermal 15°C
kW (1)
GF49T
Min. 100% P.T. l/h g/h l/h
Min.
- 15 - 1588 - 3175
- 15 - 1846 - 3693
- 15 - 465 1183 930
408 1022 816
- 15 - 465 1183 930
613 1116 1227
- 15 - 613 1116 1227
- 15 - 613 1116 1227
- 15 - 613 1116 1227
Nozzle marking Ø 1/100
TA = Open all
GF99T
g/h
-
-
2366
2044
2366
2332
2332
2332
2332