Appendix; Troubleshooting - Pioneer PDP-6010FD Manual De Instrucciones

Appendix

Chapter 15
Appendix

Troubleshooting

Problem
GENERAL
• No power.
• Power is suddenly turned off.
• The system cannot be operated.
• Remote control unit does not operate.
• POWER ON indicator or STANDBY
indicator is quickly flashing.
PICTURE/SOUND
• No image and audio is presented.
• No picture.
• Screen appears dark
• Audio is output but no image is
presented.
• Images are presented but no audio is
output.
• Sound is reversed between the right and
left.
• Sound is output from only a single
speaker.
• Picture is cut off.
• Strange color, light color, dark or color
misalignment.
Possible Solution
• Is the power cord disconnected? (See page 31.)
• Has  been turned on? (See page 33.)
• Check if you pressed TV  on the remote control unit. (See page 33.)
If the indicator on the system lights up red, press TV  on the remote control unit or STANDBY/ON on the
plasma display.
• Is the sleep timer set? (See page 65.)
• Check the power control setting. (See page 64.)
• The system's internal temperature has increased. Clean the vents, or remove any blocking objects.
(See page 17.)
• External influences such as voltage malfunction, static electricity, etc., may cause improper operation.
In this case, operate the system after first turning off the power of the plasma display, or unplugging the
power cord and re-plugging it in after one to two minutes.
• Check if TV  is off. Turn the button on when the POWER ON and STANDBY indicators are off.
• Is the Mode switch set correctly? Slide it to the TV position. (See page 16.)
• Are batteries inserted with connect polarity (+, –)? (See page 32.)
• Are batteries worn out? (Replace with new batteries.) (See page 32.)
• Operate the remote control unit while pointing it toward the remote control sensor on the plasma display.
(See page 32.)
• Are you using it under strong or fluorescent lighting?
• Is a fluorescent light illuminating the remote control sensor?
• Check if any obstacles exist between the remote control unit and the remote control sensor.
• Internal protective circuits may have been activated.
First turn  off on the plasma display, wait one minute or more, then switch the power on again by turning 
on. If the indicator is still flashing, unplug the plasma display's power cord from the power outlet. Wait one to
two minutes, then plug in the plasma display again. If this does not solve the problem, contact the nearest
Pioneer Authorized Independent Service Company, or the Customer Support Division (see back cover).
• Check if the input source for video or PC has been unintentionally selected although you want to watch a TV
channel. (See page 34.)
• Check if you have activated the Parental Control function. (See page 44.)
Enter a password to temporarily cancel the Parental Control function. (See page 48.)
• Check the cable connection with the antenna. (See page 30.)
• Check the cable connection with the other equipment. (See pages 70 to 75.)
• Is connection to other components correct? (See pages 70 to 75.)
• Is a non-compatible PC signal being input? (See page 74.)
• Is picture adjustment correct? (See page 61.)
• Check if any obstacles exist in front of the Room Light Sensor. (See pages 14 and 69.)
• Check if you have selected "Picture Off" for Energy Save. With this option selected, the screen is deactivated;
only audio is output. To restore the screen display, press any button other than VOL +/– and MUTING. (See
page 64.)
• Check if you have selected the minimum volume. (See page 35.)
• Check if you have muted sound. (See page 35.)
• When using a video or PC input source, check that the audio terminals are also connected.
(See pages 70 to 74.)
• Check if the speaker cable connections have been reversed between the right and left or if the speaker cable
from either speaker has been disconnected. (See page 25.)
• Has the balance been correctly adjusted? (See page 63.)
• Is the image position correct? (See page 66.)
• Has the correct screen size been selected? (See page 68.)
• Adjust the picture tone. (See page 61.)
• Is the room too bright? The picture may look dark in a room that is too bright.
15
93
En