Use.......................................................................................... 10
Unpacking .................................................................................10
Location ....................................................................................10
Interventions ............................................................................10
Plumbing ..................................................................................10
WARRANTY ........................................................................10
SETTING ............................................................................. 13
COMMISSIONING ..............................................................13
Rinsing ......................................................................................14
OPERATION ........................................................................ 14
Salt refill....................................................................................14
Power cut .................................................................................14
Stand-by mode .........................................................................14
-10-
Thank you for your trust in BWT by purchasing
this softener.
IMPORTANT: before any hydraulic or electrical
connection, commissioning, use or mainte-
nance, please read carefully this manual. The
non-compliance with its instructions may void
warranty.
REQUIREMENTS FOR USE
USE
This device is not designed for treating non-
drinking water. Therefore, if it delivers drinking
water, it must exclusively be connected to a
water supply already in compliance with the
requirements set by the applicable standards.
UNPACKING
Check that the device and its packing have not
been damaged during transportation. Do not
use the device in case of any visible damage,
and contact the vendor.
LOCATION
The device location shall be:
• flat, clean, dry, properly ventilated and not
accessible to unauthorized persons.
• protected from bad weather, heat sources and
chemical product vapors.
INTERVENTIONS
The owner of the appliance holds the responsi-
bility for making sure that any installation, care
or maintenance work is carried out by a duly
authorized person, with proper skills and tools,
and fully aware of this manual content.
The work shall be performed according to the
state of art and the standards applicable in the
room where the device is installed, especially
regarding plumbing, electricity and handling of
chemical products (see here-below).
PLUMBING
It is especially important to fit efficient water-
hammer arresters if the softener input and/
or output are connected to devices likely to
generate water-hammer effects (for example,
solenoid valves).
ELECTRICAL CONNECTION
Avoid any intermediate connecting device
(extension cord, power strip) between the device
and the wall outlet.
Check the circuit compliance towards all appli-
cable electricity standards, especially regarding
electrical grounding as well as electrical safety.
Do not try to connect the device if its power
supply wire is damaged. Please contact the
vendor in order to get a new complete set of
wire + transformer.
Before plugging the device to the wall outlet,
cut off the power on this outlet by using the
concerned circuit breaker or by removing the
concerned fuse.
If the device is installed close to any equipment
with high electromagnetic parasites emissions
(such as a high power transformer), it is neces-
sary to reinforce its standard protection towards
usual parasites by the proper parasite arrester
system and a shielded wire.
Do not open the electrical controller of the
device without the proper qualification. Elec-
trocution hazard.
CHEMICAL PRODUCTS HANDLING
Chemicals may be necessary for certain servicing
operations. The user shall be fully aware of any
hazard involved in those and use the proper
personal or collective protective equipment
accordingly.
Code P0011144GR - Rev 16 - 04/01/2022
The unit's surfaces must not be cleaned with any
alcohol or alcohol-based product, nor with any
product containing plastic solvents.
INTEGRITY OF THE DEVICE
The unit must not be modified or tuned without
the manufacturer's prior written approval.
APPLICABLE STANDARDS
This device is in compliance with:
• Directive 2014/30/UE on electromagnetic
compatibility.
• Directive 2014/35/UE on electrical equipment
intended for use within certain voltage limits.
• Directive 2006/42/UC dated 17/05/2006 on
machinery, and amending Directive 98/37/EC
• Directive RED 2014/53/UE making radio
equipment available on the market.
• Directive 2011/65/UE dated 08/06/2011 on
the restriction of the use of certain hazardous
substances in electrical and electronic equip-
ment, amending Directive 2002/95/EC
• This product is subject to Directive 2014/68
/ EU of 15/05/2014 relating to pressure equip-
ment. It meets the requirements of Article 4
point 3 (design and manufacture in the state of
the art in use) but does not fall into categories
I to IV and, as such, is not concerned by the CE
marking for pressure equipment.
• Protection against pollution of potable water
in water installations and general requirements
of devices to prevent pollution by backflow (In
accordance with the legislation in force).
• EN 973 standard for sodium chloride type A
for the regeneration of ion exchangers used to
soften drinking water.
• The acoustic pressure level is below 70 dB.
• [garbage bin pictogram] this
symbol proves that the device
complies with the European Di-
rective on Waste Electronic and
Electrical Equipment (WEEE):
electrical and electronic components shall be
separately thrown to proper trash bins, and
their disposal, compliant with instructions, will
support the reduction of bad consequences as
well as possible hazards towards environment
and human health.
WARRANTY
The warranty complies with the local laws of the
country where the device is sold, with possible
add-ons provided by its brand.
Please look for details on the website of your
brand vendor, most of the time on the pages
dealing with Service.
The warranty is voided in the following cases:
- installation on non-drinking water
- non compliance with the requirements of this chapter
- non compliance with the installation instruc-
tions (see § INSTALLATION PROCEDURE)
- non compliance with the maintenance instruc-
tions (see § ROUTINE & ADVANCED MAINTENANCE)
- non compliance with environmental specifi-
cations (see § TECHNICAL FEATURES)