Castelgarden XK4 165 HD Instrucciones De Uso página 55

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 92
2.4.10 Hour meter (2:P)
Indicates the number of working hours. Only
works when the engine is running.
2.4.11 Cutting height adjustment (4, 5:J)
The machine is equipped with a control for using
the cutting deck with electrical cutting height ad-
justment.
The switch is used to adjust the cutting
height in continuously variable positions.
The cutting deck is connected to the contact (2:Q).
2.4.12 Clutch release lever
A lever for disengaging the variable transmission.
4WD is equipped with two levers, connected to the
rear axle (6:A) and the front axle (6:B).
The disengagement lever must never be
between the outer and inner positions.
This overheats and damages the trans-
mission.
The levers enable the machine to be moved by
hand without the help of the engine. Two positions:
1. Lever in the inner position –
transmission engaged for normal
operation.
2. Lever in the outer position –
transmission disengaged. The
machine can be moved by hand.
The machine may not be towed over long distances
or at high speeds. The transmission could be dam-
aged.
The machine must not be operated with
the forward most lever in the outer po-
sition. Risk of damage and oil leakage in
the front axle.
2.4.13 Seat (1:T)
The seat can be folded and adjusted front-
rear. The seat can be adjusted as follows:
1. Move the control lever (1:S) upwards.
2. Set the seat to the desired position.
3. Release the control lever (1:S) to lock
the seat.
The seat is equipped with a safety switch that is
connected to the machine's safety system. This
means that certain dangerous activities are not pos-
sible when there is nobody sitting on the seat. Also
see 4.4.2.
All manuals and user guides at all-guides.com
ENGLISH
2.4.14 Engine casing (7:U)
The engine casing is opened as follows:
1. Undo the rubber strap (7:V) at the front edge of
2. Carefully lift the engine casing back.
Close in the reverse order.
2.4.15Quick-release mounting (8:H)
• Normal position with fully tensioned belt.
• 4 cm behind the normal position with slackened
As the belt idler is released from the belt, the quick
connections simplify belt and deck replacement,
and also make shifting to the washing position and
service positions easier.
Releasing the belt tension:
1. Remove the locking pins (8:G) from both sides.
2. Open the quick connections by depressing their
3. Carry out the necessary corrective action, e.g.:
• Unhook the belt.
• Replace the deck by unhooking the deck arms.
Tensioning the belt:
First tension one side and then the other according
to the instructions below.
1. Place your foot on the lever (9:J) and carefully
2. Install the locking pin (8:G).
3. Carry out the above on the other side.
In order to access the fuel cock, battery
and engine, the machine has an engine
casing that can be opened. The engine cas-
ing is locked with a rubber strap.
the casing.
The machine may not be operated un-
less the engine casing is closed and
locked. Risk of burns and crushing in-
juries.
The quick connections can be separated,
which makes it very easy to shift between
the different implements.
The quick connections allow the deck to
be moved easily between the two posi-
tions:
belt so that the deck gets closer to the base ma-
chine.
rear sections with your heel. See (8:F).
When the quick connections are
opened, the deck arms rest loosely in
the shaft sections. The deck must never
be set to the service position or washing
position without relocking the quick
connections after unhooking the deck
belt.
See fig. 10.
Do not turn the lever using your hands.
Risk of crushing injuries.
turn a half turn forwards.
EN
55

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Xk4 180 hd

Tabla de contenido