Publicidad
Idiomas disponibles
Idiomas disponibles
Original instructions
Table of Contents
1. Declaration of Conformity
2. Specified Conditions of Use
3. General Safety Information
4. Special Safety Instructions
5. Overview
6. Setup and transport
7. Machine Details
8. Initial Operation
9. Operation
10. Care and Maintenance
11. Tips and Tricks
12. Accessories
13. Repairs
14. Environmental Protection
15. Troubleshooting Guide
16. Technical Specifications
1. Declaration of Conformity
We, being solely responsible, hereby declare that
these chop and mitre saws, identified by type and
serial number *1), meet all relevant requirements
of directives *2) and standards *3). Technical
documents for *4) - see page 4.
For UK only:
We as manufacturer and authorized person
to compile the technical file, see *4) on page
4, hereby declare under sole responsibility that
these chop and mitre saws, identified by type and
serial number *1) on page 4, fulfill all relevant
provisions of following UK Regulations S.I. 2016/
1091, S.I. 2008/1597, S.I. 2012/3032 and
Designated Standards EN 62841-1:2015, EN
62841-3-9:2021, EN IEC 63000:2018
2. Specified Conditions of Use
The mitre saw is suited for longitudinal and cross
cuts, inclined cuts, mitre cuts and double mitre
cuts.
Only for KGS...: In addition, it can also create
grooves.
Only materials for which the respective saw blade
is suited may be machined (approved saw blades
see chapter 12. Accessories).
The permitted dimensions of the workpieces must
be complied with (see chapter 16. Technical
Data).
Workpieces with round or irregular cross-section
(such as firewood) must not be cut, as they
cannot be held securely during the cutting
process. When sawing a thin workpiece laid on its
edge, a suitable guide must be used for firm
support.
Any other use does not comply with the intended
purpose. Unspecified use, modification of the
device or use of parts that have not been tested
and approved by the manufacturer can cause
unforeseeable damage!
3. General Safety Information
For your own protection and for the
protection of your electrical tool, pay
attention to all parts of the text that are
marked with this symbol!
WARNING – Reading the operating
instructions will reduce the risk of injury.
Pass on your power tool only together with these
documents.
General Power Tool Safety Warnings
WARNING – Read all safety warnings,
instructions, illustrations and
specifications provided with this power tool.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
Keep all safety instructions and information
for future reference! The term "power tool" in the
warnings refers to your mains-operated (corded)
power tool or battery-operated (cordless) power
tool.
3.1 Work area safety
a) Keep work area clean and well lit. Cluttered
or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
3.2 Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do not use
any adapter plugs with earthed (grounded)
power tools. Unmodified plugs and matching
outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or
grounded surfaces, such as pipes, radiators,
ranges and refrigerators. There is an increased
risk of electric shock if your body is earthed or
grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
e) When operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the
risk of electric shock.
f) If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
3.3 Personal safety
a) Stay alert, watch what you are doing and
use common sense when operating a power
tool. Do not use a power tool while you are
tired or under the influence of drugs, alcohol
or medication. A moment of inattention while
operating power tools may result in serious
personal injury.
b) Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
your finger on the switch or energising power tools
that have the switch on invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the device may result
in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing
or jewellery. Keep your hair and clothing away
from moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust extraction can reduce dust-
related hazards.
h) Do not let familiarity gained from frequent
use of tools allow you to become complacent
and ignore tool safety principles. A careless
action can cause severe injury within a fraction of a
second.
3.4 Use and handling of the power tool
a) Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
b) Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired.
c) Disconnect the plug from the power source
and/or remove the battery pack, if detachable,
from the power tool before making any
adjustments, changing accessories, or
storing power tools. Such preventive safety
measures reduce the risk of starting the power tool
accidentally.
d) Store idle power tools out of the reach of
children. Do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.
e) Maintain power tools and accessories with
care. Check for misalignment or binding of
moving parts, breakage of parts and any other
condition that may affect the power tool's
operation. If damaged, have the power tool
repaired before use. Many accidents are caused
by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories, tool bits
etc. in accordance with these instructions.
taking into account the working conditions
and the work to be performed. Use of the power
tool for operations different from those intended
could result in a hazardous situation.
h) Keep handles and grasping surfaces dry,
clean and free from oil and grease. Slippery
handles and grasping surfaces do not allow for
safe handling and control of the tool in unexpected
situations.
3.5 Battery tool use and care
a) Always charge the batteries only in
chargers recommended by the manufacturer.
Chargers designed for a specific type of battery
may pose a fire hazard when used together with
other battery types.
b) Use only the batteries provided for this
purpose in the power tools. Use of any other
battery packs may create a risk of injury and fire.
c) When battery pack is not in use, keep it
away from other metal objects, like paper
clips, coins, keys, nails, screws or other small
metal objects, that can make a connection
from one terminal to another. Shorting the
battery terminals together may cause burns or a
fire.
d) Under abusive conditions, liquid may be
ejected from the battery. Avoid contact. If
contact accidentally occurs, flush with water.
If liquid contacts eyes, additionally seek
medical help. Escaping battery fluid can cause
skin irritation or burns.
e) Do not use damaged or modified batteries.
Damaged or modified batteries may behave
unpredictably and lead to fire, explosion or risk of
injury.
f) Do not expose the battery pack to fire or
excessive temperatures. Fire or temperatures
above 130 °C can cause an explosion.
g) Follow all instructions on charging and
never charge the battery or the cordless tool
outside the temperature range indicated in the
operating instructions. Charging improperly or
at temperatures outside the specified range may
damage the battery and increase the risk of fire.
3.6 Service
a) Have your power tool serviced by a
qualified repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
b)Never service damaged batteries. Any
servicing of batteries should only be carried out
by the manufacturer or authorised customer
service points.
3.7 Additional Safety Instructions
– These operating instructions are intended for
people with basic technical knowledge
regarding the operation of a machine like this or
similar electrical power tools. Inexperienced
persons are strongly advised to seek competent
ENGLISH en
13
Publicidad
