Descargar Imprimir esta página

Metabo KS 216 M Manual Original página 19

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 44
N Saw blade Multi Cut
305 x 30 x 2.8/2.0 96 FZ/TZ 5° neg,
for longitudinal and transverse cuts in coated
materials, laminate, plastic and aluminium profiles
Saw blades for KGS 18 LTX BL 216:
O Saw blade "cordless cut wood - classic"
628065000
216 × 1.8 / 1.2 × 30 40 WZ 5°
for longitudinal and transverse cuts in solid wood
and chipboard
Saw blades for KGS 18 LTX BL 254:
P Saw blade "cordless cut wood - classic"
628690000
254x2,2/1,6x30mm 48 WZ
for longitudinal and transverse cuts in solid wood
and chipboard
Saw blades for KGS 18 LTX BL 305:
Q Saw blade "cordless cut wood - classic"
628693000
305x2,2/1,6x30mm 56 WZ
for longitudinal and transverse cuts in solid wood
and chipboard
For a complete range of accessories, see
www.metabo.com or the catalogue.
13. Repairs
Danger!
Repair of power tools must be carried out by
qualified electricians only!
A defective mains cable must be replaced only
with a special, original mains cable from Metabo
available from the Metabo service.
If you have Metabo power tools that require
repairs, please contact your Metabo service
centre. For addresses see www.metabo.com.
You can download a list of spare parts from
www.metabo.com.
14. Environmental Protection
Observe national regulations on environmentally
compatible disposal and on the recycling of
disused machines, packaging and accessories.
Packaging materials must be disposed of
according to their labelling in accordance with
municipal guidelines. Further information can be
found at www.metabo.com in the "Service"
section.
Only for EU countries: never dispose of
power tools in your household waste!
According to European Directive 2012/19/
EU on Waste from Electric and Electronic
Equipment and implementation in national law,
used power tools must be collected separately
and recycled in an environmentally-friendly
manner.
15. Troubleshooting Guide
Following you will find a description of problems
and faults that you may remedy yourself. If the
corrective measures described here do not help,
kindly refer to chapter 13. "Repairs".
Danger!
There are particularly many accidents in
connection with problems and faults. Therefore
keep in mind:
• Prior to each correction of faults, pull the mains
plug or remove the detachable battery pack
(32).
• Check to see that all safety devices are
operational after each fault service.
No trimming function
Transport lock activated:
• pull out transport lock.
Cutting power too low
Saw blade blunt (possibly tempering marks on
blade body);
Saw blade unsuitable for the material (see
chapter 12."Accessories");
Saw blade contorted:
• Replace saw blade (see chapter 10.
"Maintenance").
628091000
Saw vibrates strongly / saw blade does not
run in a circular manner
Saw blade contorted:
• Replace saw blade (see chapter 10.
"Maintenance").
Saw blade not installed properly:
• Install saw blade properly (see chapter 10.
"Maintenance").
• Turn the saw blade toward the interior flange in
this position if necessary.
Turntable hard to turn
Chips under turntable:
• remove chips.
Cutting line indicator light is very weak
When using wood rich in resin, the LED may
become soiled.
• In this case, clean the lens with benzine.
16. Technical Specifications
Explanatory notes regarding the specifications on
page 4.
Subject to change in accordance with technical
progress.
U
= mains voltage / voltage of battery pack
I
= Rated power
F
= Min. fuse protection
P
= rated input power
1
IP
= protection class
n
= No-load speed
0
v
= Max. cutting speed
0
D
= saw blade diameter (outer)
d
= saw blade hole (inside)
b
= max. tooth width of the saw blade
A
= dimensions (lxwxh)
m
= weight
Requirements for chip and dust extraction unit:
D
= connection diameter of the extraction
1
nozzle
D
= minimum air throughput
2
D
= minimum negative pressure at extraction
3
nozzle
D
= minimum air speed at extraction nozzle
4
Maximum cross-section of workpiece, see table
on page 4.
Values measured as per EN 62841.
Permitted ambient temperature during operation:
-20 °C (-4°F) to 50 °C (120°F) (limited performance
with temperatures below 0 °C (32°F)). Permitted
ambient temperature for storage: 0 °C (32°F) to 30
°C (86°F).
Recommended ambient temperature when
charging: 0 °C to 40 °C
~
AC Power
direct current
Machine in protection class II
The technical specifications quoted are subject to
tolerances (in compliance with relevant valid
standards).
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. The actual load may be
higher or lower depending on operating
conditions, the condition of the power tool or the
accessories used. Please allow for breaks and
periods when the load is lower for assessment
purposes. Arrange protective measures for the
user, such as organisational measures based on
the adjusted estimates.
Typical A-effective perceived sound levels
(according to EN 62841):
L
= sound pressure level
pA
L
= acoustic power level
WA
K
, K
= Uncertainty
pA
WA
Wear ear protectors!
ENGLISH en
19

Publicidad

loading