Publicidad
Idiomas disponibles
Idiomas disponibles
Fixtured Tightening Module
Product Specific Instructions
Installation
General Installation Safety
• Always make sure that the drive unit/controller is
switched off before connecting/disconnecting the tool ca-
ble.
• Always disconnect the tool from the drive unit/controller
before making any adjustments on or inside the tool.
• The tool with its drive/controller box is designed to oper-
ate at any setting within its torque range at a primary volt-
age of nominal 230V/ 50Hz alternatively 115V/ 60Hz,
single phase. Refer to the manual for the drive unit or
controller.
• Make sure that the tool is in good working order and that
the controller is correctly programmed before use to
avoid unexpected behavior from the tool which may re-
sult in operator injury.
General Installation Safety
WARNING Crushing Hazard
Never place the Screw Feeding Unit on an unsecured sur-
face. Due to vibrations, the Screw Feeding Unit can
move on the surface it is placed on and fall, thus result-
ing in serious bodily injury.
Secure the Screw Feeding Unit from falling.
►
Place the Screw Feeding Unit where there is a stop
►
edge or a surface with a suitable recess.
WARNING Crushing Hazard
Never transport or carry the Screw Feeding Unit unas-
sisted. The Screw Feeding Unit is heavy and if dropped,
it can result in serious bodily injury.
The Screw Feeding Unit may only be transported
►
with the aid of suitable hoists with optional suspen-
sion.
Two people must carry the Screw Feeding Unit using
►
the handles.
CAUTION Trip and Entanglement Hazard
Prevent trailing cables by plugging in equipment as close
to where it needs to be as possible. For stationary equip-
ment, if trailing cables are unavoidable use cable ties and
cover strips.
• Refer installation to qualified personnel only.
Air supply and connection hazards
WARNING High Air Pressure and Projectile Hazard
Always verify that all connections between the Feeding
Tube and the Swivel Arm are securely fastened before
pressurizing the tool. Otherwise screws can escape at
high speed and cause serious injury, especially to the
eyes.
For this reason, the pneumatic power supply must be
►
switched off and vented during all work on the
Screw Feeding Tightening Module, or the "Bit
Change" mode must be set on the Screw Feeding
Unit.
• Air under pressure can cause severe injury.
© Atlas Copco Industrial Technique AB - 9846 0328 00
• Do not exceed maximum air pressure of 6.3 bar / 90 psig,
or as stated on tool nameplate.
Electrical hazards
DANGER Electric Hazard
Touching live parts causes an immediate risk of death.
The mains current, voltage, and frequency must be
►
the same as the type plate.
Grounded screw fastening systems must be con-
►
nected to properly installed and grounded power out-
lets. The grounding pin must never be removed. The
plug must not be manipulated in any way. Adapter
plugs are not allowed.
Additional Installation Safety Messages
WARNING General Attention
To avoid serious or fatal injury, ensure that you are fa-
miliar with the system and safety information before you
use the system.
Pay particular attention to all safety messages and
►
precautions.
Always follow the instructions in this publication.
►
Do not use the instrument in a way that is not de-
►
scribed in this publication.
Store all publications in a safe and easily retrievable
►
place.
WARNING Trip and Entanglement Hazard
There is a risk of falling and tripping while using trailing
cables during installation. This may lead to minor in-
juries.
Prevent trailing cables by plugging in equipment as
►
close to where it needs to be as possible. For station-
ary equipment, if trailing cables are unavoidable, use
cable ties and cover strips.
Refer the installation to qualified personnel only.
►
Hang the tool securely using a balancer. When using
►
a suspension yoke, check that it is in good condition
and correctly fastened.
WARNING Moving Parts Hazard
There is a risk of tool cables jamming during installation.
This may lead to severe injuries and property damages.
Shut off the air supply, drain the hose of air pressure,
►
and disconnect the tool from the compressed air line
before installing the product.
Keep hands and fingers away from moving parts.
►
WARNING Falling Down Parts Hazard
Incomplete or incorrectly installed systems can lead to
loosening and dropping of the tool. It may lead to serious
injuries.
The screw connections must always be tightened ac-
►
cording to the manufacturer's instructions.
Only the screws recommended by the manufacturer
►
should be used.
Damaged screws must never be used.
►
Safety Information
5
Publicidad
