Delta 36-6013 Manual De Instrucciones página 2

FEATURES .......................................................................... 2
IMPORTANT SAFETY INSTRUCTIONS ............................... 4
SAFETY SYMBOLS-DEFINITIONS ...................................... 4
GENERAL POWER TOOL SAFETY WARNINGS .................... 5
TABLE SAW SAFETY RULES ............................................... 6
TERMINOLOGY .................................................................. 6
TABLE SAW SPECIFIC SAFETY RULES .................................. 6
SAW BLADE GUARD, ANTI-KICKBACK PAWLS AND RIVING
KNIFE ASSEMBLY ............................................................... 8
KICKBACKS ....................................................................... 8
PROPOSITION 65 WARNING ............................................ 8
POWER CONNECTIONS ..................................................... 9
POWER SOURCE ................................................................ 9
DOUBLE INSULATION ........................................................ 9
ELECTRICAL CONNECTION ................................................. 9
POLARIZED PLUGS ............................................................ 9
EXTENSION CORDS ........................................................... 9
UNPACKING ..................................................................... 10
PACKAGE CONTENTS ....................................................... 10
HARDWARE BAG CONTENTS ............................................ 11
ASSEMBLY ....................................................................... 12
TOOLS NEEDED FOR ASSEMBLY OR ADJUSTMENTS ........... 12
ASSEMBLING THE STAND ................................................. 13
ATTACHING STAND TO SAW ............................................. 14
HEIGHT ADJUSTMENT KNOB INSTALLATION ..................... 15
INSTALLING THE BLADE .................................................. 15
THROAT PLATE ................................................................ 16
ANTI-KICKBACKS PAWLS AND BLADE GUARD .................... 17
INSTALLING FENCE ......................................................... 18
REMOVING FENCE ........................................................... 18
ON-BOARD STORAGE ....................................................... 19
MAKING ADJUSTMENTS .................................................. 20
LEVELING THE THROAT PLATE ......................................... 20
ADJUSTING BLADE PARALLEL TO
MITER GAUGE GROOVE (HEEL)
SQUARING THE BLADE VERTICALLY ................................. 21
ADJUSTING THE BEVEL STOPS ......................................... 22
ADJUSTING THE BLADE HEIGHT....................................... 23
CHANGING THE BEVEL .................................................... 23
ADJUSTING RAIL SYSTEM ................................................ 23
The DELTA 36-6013 series 10 inch Portable Contractor Table Saw
®
is designed for portability and high quality performance. It includes:
basic machine, sturdy tubular steel stand, integral 2 1/2 inch dust
chute, a fence system, T-slot miter gauge, 15-amp motor, on/off
switch, cast aluminum table, extension wing, see-through blade
guard with anti-kickback pawls, and 10 inch carbide blade.
This tool can ONLY be used with woodworking saw blades.
NOTICE: The manual cover illustrates the current production model. All other illustrations contained in the manual are representative
ONLY and may not be exact depictions of the actual labeling or accessories included. They are intended for illustrative purposes ONLY.
TABLE OF CONTENTS
........................................ 20
FEATURES
USING COLOR-CODED SCALES ......................................... 24
ADJUSTING EXTENSION TAB PARALLELISM ....................... 25
RIVING KNIFE POSITION AND ALIGNMENT ................... 26
RIVING KNIFE HEIGHT SETTING ...................................... 26
PARALLEL ALIGNMENT ..................................................... 27
HORIZONTAL ALIGNMENT ................................................ 27
VERTICAL ALIGNMENT ..................................................... 27
OPERATION ..................................................................... 28
DUST COLLECTION .......................................................... 29
TURNING THE SAW ON AND OFF ..................................... 29
TRANSPORTING THE SAW ................................................ 29
MAKING CUTS ................................................................. 30
RIP CUTS ........................................................................ 31
BEVEL RIPPING ............................................................... 31
CROSSCUTTING............................................................... 32
BEVEL CROSSCUTTING .................................................... 32
MITER CUTS ................................................................... 32
COMPOUND MITER CUTS ................................................. 33
LARGE PANEL CUTS ......................................................... 33
NON-THROUGH CUTS ...................................................... 33
MAKING A NON-THROUGH CUT ........................................ 33
CUTTING AIDS AND ACCESSORIES ................................. 34
PUSH STICK .................................................................... 34
USING THE MITER GAUGE ............................................... 34
AUXILIARY MITER GAUGE FACING .................................... 35
AUXILIARY FENCE (FLIP DOWN) ....................................... 35
PUSH BLOCK .................................................................. 35
GROOVING AND RABBETING ........................................... 35
FEATHERBOARD ............................................................. 36
CUT OFF GAUGE.............................................................. 36
JIGS................................................................................ 36
MAINTENANCE ................................................................ 37
KEEP MACHINE CLEAN ..................................................... 37
MAINTENANCE REMINDERS ............................................. 37
ACCESSORIES .................................................................. 38
TROUBLESHOOTING ........................................................ 38
PARTS, SERVICE OR WARRANTY ASSISTANCE ............... 39
SPECIFICATIONS
Max depth of cut at 90 degrees:
Max depth of cut at 45 degrees:
Max rip to right of blade:
Max rip to left of blade:
MOTOR SPECIFICATIONS:
Amps
Voltage
No Load RPM
Blade Diameter
2
3 1/2 inch
2 1/2 inch
25 inch
12 inch
15
120
5,000
10 inch