Kellys CITY Instrucciones De Uso página 12

GB
OWNER'S MANUAL
and cause severe injury to child and rider.
The carrier is not designated for transport of animals. Do not carry persons and oversized loads
on bicycle carrier. The carrier is not designated for attaching of any trolleys. Do not modify carrier
construction. Each construction change influence inevitably designed carrier properties.
Do not exceed permissible maximum carrier load of 25 kg. Do not exceed permissible total weight of
the rider plus luggage for this bicycle when luggage is loaded on carrier.
The carrier assembled to this bicycle meets EN14872 requirements.
LIGHTING
If your bicycle is equipped with front and rear lighting, check their function regularly.
Dysfunctional bulb must be replaced with the new one, always with identical parameters. In case of
lack of experience with bulb changing, we recommend you to visit a bicycle service centre.
Your bicycle is equipped with front halogen light that is powered by dynamo integrated in the front
wheel hub. A switch placed on the back of front light has two positions:
• ON: lighting constantly also during the daylight
• OFF: in this position, the electric circuit is disconnected and the light is off
The rear light is connected electrically to the front light, i.e. the rear light's function is also controlled
through the switch (ON/OFF).
The rear light is equipped with a lighting function „Standlicht", when small amount of energy
generated by the dynamo integrated in front hub is stored during the ride in a capacitor, what ensures
that the LED diode in the rear light keeps lighting for a period of 4 minutes after stopping the bicycle
(recharging the capacitor requires few minutes ride at speed 20 km/h).
AUXILIARY WHEELS
If your bicycle is equipped with auxiliary wheels, then these wheels for the bicycle are delivered
disassembled. Therefore it is necessary to assemble and mount the wheels before using.
Plastic bag supplied with the holders of auxiliary wheels includes:
- 2 long screws
- 6 washers
- 2 serrated washers
- 2 common nuts
10
- 2 safety nuts (with plastic insert)
* Assembling wheel
Proceed as follows:
1. Slide the washer on the screw, then slide the wheel and slide another washer on the other side of
the wheel.
2. Screw the nut on the bolt so that the wheel freely rotates.
3. The wheel with the bolt slide into a round hole on a steel strut – the wheel must be on the outside
of the strut.
4. Further, slide the serrated washer on the screw and then another nut with which attach the wheel
to the strut. Then use the safety nut with a plastic insert.
5. Now use two wrenches of 14 mm size and tighten two nuts against each other. Make sure the
wheel rotates about the bolt lightly, but without play.
6. Repeat the procedure for the other wheel.
* Mounting the strut to the rear axle of the bicycle
Proceed as follows:
1. Grasp the strut with the mounted wheel and slide the other end of the strut into the rectangular
hole of the holder with rubberized forked end – this end must be directed to the bicycle frame and
the wheel must be on the outer side.
2. Into the rectangular hole between the strut and the holder insert one washer. Slide in this way
prepared holder with the strut onto the axis of the rear wheel of the bicycle so that the axis passes
all holes including washer.
WARNING: Do not remove the nut that secures the rear wheel in frame!
3 The rubberized end of the strut's holder must be installed to the stop of the lower rear fork of the
bicycle frame. Secure the holder on the axis by the nut with pressed washer.
4. Repeat the procedure for the other strut.
5. Then set the desired height of both auxiliary wheels and tighten the nuts to the stop.
IMPORTANT WARNING
Before every ride check whether all screws are securely tightened!
If you would not use the auxiliary wheels on your bike, then slide the washer and screw a hat-nut
(a nut with closed end) to the axis of rear wheel. This will remove dangerous edges that an uncovered
TREKKING I CITY