Publicidad
Idiomas disponibles
Idiomas disponibles
5. When the engine is running, wait a moment and
then briefly rev up using the throttle (9). Set the
choke lever (47) to the
6. To start the cutting device, press the switch lock
(4) with the palm and the throttle with the fingers
(9). The further you press the throttle lever (9), the
higher the engine speed becomes. Loosening the
throttle (9) brings the engine back into idling and
the cutting tool stops. The cutting tool must not
rotate or move while idle!
7. If problems occur, push the on/off switch (3) to
"STOP" immediately so that the engine stops.
Attention! The cutting device can keep turning for
a few seconds.
Starting the engine when warm
1. To start the motor when warm, move the choke le-
ver to the "Warm start and working"
2. Pull the handle of the starter cable (7) 3 to 5 times
to start the engine.
ATTENTION! Never put a foot on the engine drive
unit (1) or kneel on it.
Note:
If the engine does not start even after several at-
tempts, read the "Troubleshooting" section.
Note:
Always pull the start pull cord out straight. If it is pulled
out at an angle, friction will occur on the lug. This fric-
tion causes the cord to wear through and wear out
faster. Always hold the starter handle when the cord
retracts.
Never let the cord snap back from its extended state.
Note:
Do not start the engine in tall grass.
Do not start the engine if the device is hooked into the
carrying strap (28).
m Attention
In an emergency, the safety tab (b) on the carrying
strap (28) can be pulled. The machine then immedi-
ately detaches from the carrying strap (28) and falls
to the floor.
m Attention:
Use this work technique with particular care. The
greater the distance between the cutting tool and the
ground, the greater the danger that the material to be
cut and foreign objects will be thrown to the side.
10.1.2 Shutting off the engine
1. Push the on/off switch (3) to the off position
"STOP".
2. Wait until the engine has come to a standstill be-
fore setting the device down.
position.
position.
www.scheppach.com
11. Working instructions
ATTENTION:
Generally, hold the brush cutter / grass trimmer by
the insulated gripping surfaces, as the cutting device
can come into contact with hidden power cables. If
the cutting device comes into contact with an ener-
gised line, device parts can become energised and
cause an electric shock. Always ensure that you have
a secure stance and an upright working posture.
11.1 Working with the brush cutter / grass trim-
mer (13)
When working with the brush cutter / grass trimmer
(13), the brush cutter / grass trimmer shield (14) for
the blade and thread operation must be mounted in
order to prevent objects being ejected.
The brush cutter / grass trimmer shield cutting blade
(14a) in the brush cutter / grass trimmer shield (14)
automatically cuts the thread to the optimum length.
(Fig. 7)
11.1.1 Mowing with the brush cutter (13)
• With the device switched off, first familiarise your-
self with the operation and guidance if you are
working with a brush cutter (13) for the first time.
• The brush cutter (13) is designed so that it is oper-
ated solely from the right-hand side of the operator.
• Always hold the brush cutter (13) tightly with both
hands on the rear handle (5) and front handle (10).
• Hold the rear handle (5) with your right hand and
the front handle (10) with your left hand.
• Always make sure that the cutting tool continues to
rotate for a short time after the throttle lever (9) has
been released.
• Always ensure that the engine is idling properly
so that the cutting tool no longer rotates when the
throttle (9) is not pressed.
• Always work at high speed to achieve the best cut-
ting results.
• Move the device with a uniform curved movement
from left to right and back again. Then cut the next
section. (Fig. 16)
• Attention: Always move the device back into the
starting position before cutting the next path.
• If you hit a stone or another obstacle while working,
switch off the engine and remove the spark plug
connector (6). Check the brush cutter (13) for dam-
age.
• Attention: Always be particularly careful when
working in difficult terrain and on slopes. Cut long
grass in stages to ensure that the device is not
overloaded. Trim the tips first, then work your way
forward in stages.
• Always wear safety goggles and hearing protec-
tion and a safety helmet when carrying out thinning
work.
GB | 53
Publicidad
