Operation Manual (Removable - Nice SLIGHT Instrucciones Y Advertencias Para La Instalación Y El Uso

IMPORTANT – This instruction sheet contains important informa-
tion regarding safety; take care to read all instructions before using
the product. Keep this manual in a safe place to enable future use.
SAFETY WARNINGS AND PRECAUTIONS
NEVER touch parts of the automation while the gate is moving!
• Before using the automation for the first time, take care to read this oper-
ation manual provided by the automation installer. Also ensure that you are
fully informed of all origins of residual risks.
• Keep the manual for consultation when in doubt and ensure supply to
new owners of the automation.
• Your automation is a machine that performs commands imparted by the
user; negligent or improper use may constitute a hazard. Never activate
automation controls if persons, animals or objects are present in the oper-
ating range.
• Children: this automation system guarantees a high level of
safety, using special detection devices to prevent movement in the
presence of persons or objects . thereby guaranteeing constant
foreseeable and safe activation. However, it is advisable to ensure
that children do not play in the vicinity of the automation. To avoid
inadvertent activation, and remote controls should always be kept
out of reach. (the transmitter is not a toy!).
• Check the automation frequently to detect possible imbalance, signs
of wear or damage. Suspend use immediately if maintenance is required.
• Periodically check correct operation of the photocells and perform the
scheduled maintenance at least every six months.
• Photocells do not constitute actual safety devices, but safety aids. They
are designed using highly reliable technology, but in extreme conditions
may be subject to malfunctions or potential faults. CAUTION!– In certain
cases these faults are not immediately evident.
Never pass the transit area while the gate is moving!
• If any anomalous condition is noted on the automation, disconnect the
power supply from the system immediately. Never attempt to repair the
automation alone; contact your local installer for assistance. In the mean-
time the system can be used with manual Opening and Closing by manu-
ally releasing the gearmotors as described in this manual.
• In the event of a power failure, on restoral of power the first manoeuvre
command will be executed at low speed, regardless of the type of speed
set.
• Even if you possess the skills, never modify the system or automation
programming and adjustment parameters: This is the responsibility of the
automation installer.
• Testing, periodic maintenance and any repairs must be documented by
the person performing the operations and the relative documents must be
kept by the system owner.
• At the end of the automation's lifetime, ensure that it is disposed by quali-
fied personnel and that the materials are recycled or scrapped according
to current standards in the place of use.
Operation manual
(to be given to the final user)
MANUAL MOVEMENT AND RELEASE: before carrying out this opera-
tion please note that release can only occur when the leaf is stopped.
1 Slide the lock cover disc.
2 Move the leaf manually.
To lock: carry out the same procedures backwards.
Control with safety devices out of order: If the safety devices are
malfunctioning, it is still possible to control the gate.
• Operate the gate control device (remote control or key-operated
selector switch, etc.). If the safety devices enable the operation,
the gate will open and close normally, otherwise the flashing light
flashes a few times but the manoeuvre does not start (the number
of flashes de pends on the reason why the manoeuvre is not ena-
bled).
• In this case, actuate the control again within 3 se conds and keep
it actuated.
• After approximately 2s the gate will start moving in the "man pre-
sent" mode, i.e. so long as the control is maintained the gate will
keep moving; as soon as the control is released the gate will stop.
IMPORTANT! - If the safety devices are out of or d er the
au t omation must be repaired as soon as possible.
Replacing the Remote Control Battery: if your radio control, after a
period of time, seems not to work as well, or not to work at all, it may
simply be that the battery is exhausted (depending on the type of use,
it may last from several months up to one year and more). In this case
you will see that the light confirming the transmission is weak, or does
not come on, or comes on only briefly. Before calling the installation
technician try exchanging the battery with one from another operating
transmitter: if the problem is caused by a low battery, just replace it
with another of the same type.
The batteries contain polluting substances: do not dispose of them
together with other waste but use the methods established by local
regulations.
Are you satisfied? If you wish to install another automation system in
your home, call your old installation technician and use Nice products.
You will get the services of a specialist and the most advanced prod-
ucts available on the market, superior performances and maximum
system compatibility. Thank you for reading these instructions. We feel
confident that you will be well satisfied with your new sy stem: for any
present or future requirements, please contact your reliable installation
technician.
1
2
English – 19