Lowering The Vehicle; Maintenance And Care Of The System; System Maintenance Plan; As Required Or Visible Damage - Nussbaum SPRINTER MOBIL 2500 Instrucciones De Servicio

• Inspect the hazardous area.
No person or object may stand in the working area of the lift, or on the
lift.
• Switch on controls. Turn the main switch (2) to position „1" (see figure
007).
• Position polymer overlays below the points specified by the vehicle ma-
nufacturer. The polymer overlays may not be placed on edge, other-
wise the vehicle could fall.
• Lift the vehicle. Push the „LIFT" (3) button.
• If the wheels are not blocked, interrupt the lifting process and check for
proper seating of the polymer overlays.
• Raise the vehicle to the desired working height.
• Then position the operating unit in such a way that the flexible hose pa-
ckage (protective and hydraulic hose) cannot be damaged by exter-
nal influences (such as being driven over by the load)
5.2

Lowering the vehicle

!
Warning! The hydraulic lines may not be driven over. This can lead to
damage and, if leaks result, even to the lift sinking.
• Inspect the hazardous area. No person or object may stand in the wor-
king area of the lift, or on the lift.
!
The vehicles cannot be lowered into the lowest position without
wheels. Otherwise the lift cannot raise the load using its own force.
The vehicle could be damaged.
• Lower the vehicle to the desired working height. Push the „LOWER" but-
ton (4) (see figure 007).
• The system is equipped with an optional CE-STOP
During „LOWER" (4) to the lowest position, the system stops at a height of
300 mm.
To allow the system to lower further, it is necessary to release the „LOW-
ER" button (4) and press it again.
A signal tone sounds until the system has reached the lowest position.
• The entire lowering process must be observed.
• If the lift is in the detectable lowest position, remove the polymer over-
lays and drive the vehicle from the lift
20110005 SPRINTER MOBIL 2500-3000 - HYMAX PRO 2500-3000 OPI
6

Maintenance and care of the system

Before maintenance, do all preparation work so there
is no danger to life or limb or object damage during
maintenance and repair work.
Value is placed on long lifetimes and safety in the development and pro-
duction of Nußbaum products. To guarantee the safety of the operator,
product reliability, low running costs, keep the warranty and also the long-
lifetime of the product, proper set up and operation is just as important as
regular maintenance and sufficient care.
Our platforms fulfil or exceed all safety standards of the countries we sup-
ply to. For example, European regulations require a service by qualified
experts every 12 months of work of the platform. To guarantee the largest
possible availability and functional capacity of the lift system, ensure the list
of any cleaning, care and maintenance work is done.
The lift system is to be serviced at regular intervals according to the fol-
lowing plan. For intensive operation and higher degree of contamination
shorten the service interval.
The complete function of the lift system is to be observed during daily use.
Customer service must be informed of any malfunctions or leaks.
To simplify maintenance work, follow instructions on the maintenance sti-
cker that is found somewhere on the unit, depending on the lift design.
6.1

System maintenance plan

Before beginning service, disconnect from power. The
system is to be secured against unintentional lowering
and unauthorized access.
6.1.1

As required or visible damage

6.1.2

Maintenance 1 x per year

• Check condition of the model plate, load capacity and sticker. Ex-
change them if damaged or illegible.
• Check condition of the Model plate, load capacity and sticker. Ex-
change them If damaged or illegible.
015
• Free the piston rod of the lifting cylinder of sand and dirt.
• Check the wiper for damage.
• Moving parts such as joint bolts and DU bearings, sliding pieces, sliding
surfaces and rollers are to be cleaned and checked for wear, exchange
if required.
• Moving parts such as joint bolts, sliding pieces and sliding surfaces are
to be cleaned and checked for wear and lightly greased. Do not over-
lubricate.
• Check the polymer overlays and replace if required.
• Check all available safety devices for function.
• Check the state and function of the mobile set.
• Check ease of motion of the tow bar (8), guide roller (6) and wheel
axles (9).
• According to manufacturer instructions, the hydraulic oil should be
changed every two years in normal operations. Various environmental
influences e.g. location, temperature swings, intensive operation etc.,
can have an influence on the quality of the hydraulic oil. For this reason,
the oil must be checked during annual safety inspections and mainte-
nance.
The oil is used if it has a milky colour or if the hydraulic oil smells un-
pleasantly.
Version 1.0
31