Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
6.1 connecting the Isoclick fix® arms in a
rearward-facing installation (optional).
1. Make sure the Isoclick Fix arms are displayed to
install the car seat forward facing (group 1/2/3)
(fig. 9).
2. Place the seat in the back seat of the vehicle in the
direction of travel.
3. Hold the safety seat with both hands and insert the
two Isoclick Fix arms
(19)
firmly into the insertion
(26)
guides
until they fasten with a click on both
sides. The red button will partially change to green
on both sides (fig. 20).
4. Shake the seat to check that it is correctly anchored
to the vehicle's ISOFIX points.
6.2 fastening the seat with the vehicle's belt in a
forward-facing installation. Group 1
1. Place the seat in the back seat of the vehicle in the
direction of travel (fig. 16).
2. Take out the reducer cushion (4). Pass the
abdominal strap of the seat belt through the
lower seat guides
(11)
and underneath the seat.
Buckle the vehicle seat belt until you hear a click
(fig. 21).
3. Pass the diagonal section of the vehicle´s belt
through the rear side of the backrest cushion and
the seat backrest.
4. And continuing, pass the diagonal section of the
vehicle´s belt between the backrest and the
headrest sides (fig. 21).
5. Make sure it is as tight fitting as possible. Ensure
46
the straps are not twisted or knotted at any point.
to ensure the belt holds tighten the seat, you can
press with the knee on the seat at the same time
you are fitting the belt to the seat
For the safety of the child the following checks
should be made before every trip:
• The safety seat is firmly installed in the vehicle.
• The straps are not twisted.
• The safety seat straps are firmly fastened around
the child's body, without squashing it.
(10)
• The shoulder straps
are correctly adjusted
and not twisted.
•
The shoulder protectors (3)
are on a level with the
child's shoulders.
•
The clasps (5)
are correctly inserted into the belt
buckle (7).
7. PlAcING ThE chIld IN ThE sEAT.
GROUP 1
To install
the child correctly follow the steps
described in section 5.
8.INsTAllING ThE chIld sEAT. GROUP 2 /3
GROUP 2 /3. From 4 to 12 years
approx. (15- 36 kg)
1. Make sure the 5-point harness and harness buckle
have been correctly removed (see points 3.4).
2. Follow the steps described in section 3.8.
3. If you wish to install the car seat using the Isoclick
Fix® system, follow the instructions described in
chapter 6.1
4. Place the safety seat on the vehicle seat in the
direction of travel.
5. Place the seat in the desired position (1, 2 or 3),
(fig.18).
6. Place the child in the seat. Pull the vehicle safety belt
and pass it in front of the child until it reaches the
vehicle seat belt buckle.
IMPORTANT! Make sure the belt is not twisted.
7. Insert the clasp into the vehicle seat buckle. You
should hear a click.
8. Place the diagonal part of the belt
(27)
and the part
that crosses the lap
(28)
on the side of the vehicle
safety seat buckle, through the abdominal belt guide
(11)
of the safety seat (fig. 22 B).
9. Pass the diagonal part of the belt
(27)
through the
diagonal belt guide (group 2)
(2)
on the headrest until
it is fully extended and not twisted (fig. 22 A).
10.
Make sure the diagonal part of the belt passes
over the child's collar bone and not the neck.
IMPORTANT! The part of the abdominal belt
(28)
rest as low as possible over the child's hips, on both sides.
(2)
TIP: If the seat back covers the guide
you can raise
the headrest, which will allow you to insert the diagonal
section of the belt easily. You should then reset the
headrest to the correct height, as shown in point 3.8.
(2)
Diagonal belt
fig. 22
guide (group 2/3).
(27)
Diagonal belt
section.
(28)
Abdominal belt
section.
(29)
Vehicle's belt
buckle.
(11)
Abdominal
belt guide
29
(group 0+/1/2/3).
b
11
29
should
TIP: You can readjust the height of the vehicle
headrest.
To ensure the child's safety, the following items
should be checked before every trip:
2
A
27
28
47
Publicidad
Tabla de contenido
