位置検出器の取り付け; Installing The Synchronizer; Instalación Del Sincronizador; Installazione Del Sincronizzatore - JUKI SC-510 Manual De Instrucciones

Ocultar thumbs Ver también para SC-510:
Tabla de contenido

Publicidad

2. 位置検出器の取り付け / INSTALLING THE SYNCHRONIZER /
INSTALACIÓN DEL SINCRONIZADOR /
INSTALLAZIONE DEL SINCRONIZZATORE / 位置檢測器的安裝
4
3
7
6
5
4) 下停止位置の調整後、ミシンコントローラを1ポジション(上位置停止)にして上停止位置を確認しま
す。 上停止位置がずれている場合は、上位置検出板 5 で微調整してください。
5) 停止位置の調整後、 検出器1のカバーを取り付けます。 ミシンコントローラを2ポジション (下位置停
止)に戻します。
• Apply the adjustment below to the models which are not provided with built-in synchronizer.
Adjust the stop position in the state that the synchronizer is actually installed to the sewing machine. At this time,
remove the connector for the sewing machine for safety's sake.When you remove a connector, please be sure to
turn OFF the power. When you adjust the UP position detecting plate 5 , and when you turn the joint of synchronizer,
please be sure to turn OFF the power.
Temporarily fix synchronizer 1 to the handwheel.
1)
Remove the cover of synchronizer 1, and adjust edge section 6 of outside UP position detecting plate 5 to
2)
the position of scale of DOWN position detecting plate 7 in accordance with the respective models. For the
position of scale of the respective models, refer to the list 1.
3)
After confirming that the connectors for sewing machine have been removed, set the sewing machine controller
to position 2 (DOWN position stop), loosen setscrews 2 of synchronizer 1, turn the joint, and adjust the stop
position so that DOWN position engraved marker dot 4 aligns with engraved marker dot 3 on the machine arm.
Engraved marker dot of stop position of the handwheel changes in accordance with the respective models.
Refer to the list 2.
4)
After adjusting DOWN stop, set the sewing machine controller to position 1 (UP position stop) and confirm the UP
stop position. When UP stop position is improper, perform fine adjustment with UP position detecting plate 5.
After adjusting the stop position, attach the cover of synchronizer 1. Return the sewing machine controller to
5)
position 2 (DOWN position stop).
• 下記調整は内蔵シンクロを搭載していない機種に
1
2
適用してください。
実際にミシンに取り付けた状態で停止位置を調整して
ください。 このとき、 安全のためミシン用コネクタは
外してください。ミシン用コネクタ を外すときは、
必ず電源を OFF にしてください。 上位置検出板 5を
調整しているときと、 検出器の継手を回すときは必ず
電源を OFF にしてください。
1)検出器 1 をはずみ車に仮止めします。
2)検出器1のカバーを外し、 外側の上位置検出板5
3)ミシン用コネクタが外されていることを確認後、
– 10 –
のエッジ部 6 を下位置検出板 7 の目盛の位置に
各機種ごとにあわせてください。 各機種の目盛位
置は表 1 を参照してください。
ミシンコントローラを2ポジション (下位置停止)
にして、 はずみ車の下位置刻点4とアーム刻点3
が一致するように検出器 1 の止めねじ 2 を緩め
て継手を回し、停止位置を調整してください。
はずみ車の停止位置刻点は各機種ごとに違います
ので、表 2 を参照してください。

Publicidad

Tabla de contenido
loading

Tabla de contenido