Removing The 5-Point Harness - Babyauto MORE Dabolta 0123 Manual De Instrucciones

2. VEHICLE INSTALLATION POINTS
WHERE:
In the vehicle rear seats.
DO NOT install the safety seat in forward seats except for the
following cases:
1. Whenever the vehicle does not count with rear seats.
2. When all rear seats are already occupied by children
exceeding 135 cm height.
3. When it is not possible to install all child restraints systems
in the rear seats.
*Note: According to Spanish legislation for child restraint systems (Royal Decree 667/2015).
HOW:
GROUP 0+ • Install rearward facing.
GROUP 1 • Install forward facing.
GROUP 2/3 •Install forward facing.
In seats with:
ISOFIX anchorages (between seat and backrest) and Top Tether
anchor points (eg in the tray, on the floor or behind the backrest)
and 3-point belt (vehicle belt).
NOTICE:
The child seat must only be used in this seat IF it has ISOFIX
anchorages, top tether points a lap and diagonal belt (3 points).
3. GENERAL SEAT USE
3.1. How to use the harness buckle
1. Bring the two clasps together (fig. 3.1).
2. Make sure the correct side is facing up (fig. 3.2).
3. Fasten the two clasps together before inserting them into the harness
buckle. You should hear a click (fig. 3.3).
4. Pull the harness adjustment belt
the lap is not loose, ensuring the harness is taut and the buckle closed. Open
(F)
the harness buckle by pressing the red button (fig.3.4).
22
(H)
o that the part of the strap that covers
3.2. Harness buckle care
In order to ensure child safety it is essential that the harness works correctly. If
this is not the case it is probably because of an accumulation of dirt or foreign
bodies.
1
Incorrect operation is understood as:
• The buckle clasps are notably slow to release when the red button is pressed.
• The buckle clasps cannot be inserted (they fall out when they are inserted into
the buckle).
• The buckle clasps come together without making a click.
• It becomes difficult to insert the clasps into the buckle (resistance is felt).
• The buckle only opens when forced.
• Solution
Clean the harness buckle so that it works properly.
3.3. Cleaning the harness buckle
1. Open the buckle
2. Hold the metal plate from below in a vertical position (fig. 3.12).
3. Slide the metal plate along the slot (fig. 3.5 y 3.6).
4. Remove the buckle
2
5. Steep the buckle
hour. Rinse and dry it.

3.4. Removing the 5-point harness

1. Loosen the harness straps by pulling them at the point where they cover the
chest while pressing the harness adjustment button
2. From the back of the seat (fig. 3.9), Locate the harness strap connector and
unclip the harness straps
them by pulling them from the front of the seat (fig. 3.11).
3. Free the shoulder protectors
joins them (located at the back of the seat) or, in the event they are joined
without a connector, by passing them directly through the corresponding
holes in the seat. (fig. 3.11).
4. Lift the fabric cover and keep the harness straps folded in the corresponding
seat hollow so that they do not disturb the child. Replace the cover in its place.
5. Turn the seat over and, from the back, free the belt buckle
retention plate through the slot in the seat (fig. 3.12).
6. Remove the belt buckle
(F)
(press the red button).
(F)
(fig. 3.7).
(F)
in hot water and neutral liquid detergent for at least one
(G)
(E)
, freeing them from the connector, then remove
(C)
by unfastening them from the connector that
(F)
and save it in the storage bag.
(fig. 3.8).
(F)
by passing the
23