Removing The Cover - Babyauto MORE Dabolta 0123 Manual De Instrucciones

3.5. Removing the cover

A) Headrest.
1. Adjust the headrest to its highest position.
2. First remove the part of the cover that includes the safety belt guide
followed by the remainder of the headrest cover.
B) To remove the 5-point harness, see point 3.4. Remove the back and base
covers.
3.6. Putting the cover back on
Follow the same steps in reverse order.
IMPORTANT! When you place the buckle again in the seat, check that it is
firmly secured. Make sure that the retaining plate holds the buckle correctly.
3.7.Seat reclining positions.
This restraint system has three reclining positions. Before installing the child on
the seat, select the reclining position by pulling of the lever situated between
the seat and the base (fig. 3.13).
IMPORTANT! For the rearward facing installation, the only possible reclining
position is the number 3. In forward installation, however, you can select the
position 1 or 2 (fig. 3.15).
3.8.Adjusting the harness in an installation with a 5-point harness.
Groups 0+/1.
Proper adjustment of the height of the harness ensures the child will be seated
correctly. The harness should be adjusted to the height of the child's shoulder
or slightly above; never behind the child's back or level with the ears (fig. 3.16).
IMPORTANT! The shoulder straps should not be passed behind the child's back
at or above ear level.
1. Loosen the harness straps by pulling them gently while pressing the harness
(G)
adjustment button . (fig. 3.8).
2. To tighten the straps Pull the harness adjustment belt
the strap that covers the lap is not loose, ensuring the harness is taut and
the buckle closed. Open the harness buckle
(fig.3.4).
3.9.Adjusting the headrest. Groups 2/3.
A correctly adjusted headrest ensures that the diagonal part of the safety belt
is ideally positioned, offering the child the best possible protection.
24
(H)
o that the part of
(F)
by pressing the red button
The headrest should be adjusted so that a space equivalent to two fingers
remains between the headrest and the child's shoulders.
To adjust the height of the headrest:
(K)
1. Pull the headrest height adjuster
will unlock the headrest (fig. 3.8).
2. Now you will be able to move the headrest to the desired height. When the
adjuster is released the headrest will remain locked in the chosen position.
3. Place the safety seat on the car seat.
4. Sit the child in the seat and check the height. Repeat the process until the
correct height is achieved.
4. CAR SEAT REARWARD-FACING INSTALLATION.
GROUP 0+
GROUP 0+ only.
From birth to 12 months approx. (0-13 Kg)
IMPORTANT:
It is advisable to use the seat backward-facing as long as possible.
If necessary, the seat can be installed forward-facing when the child reaches
9kg of weight.
• Preparing the ISOFIX system
1. Extract the ISOFIX arms (Q) located at the base of the seat by pressing the
(P)
ISOFIX system unlock button
TIP: The ISOFIX fastening points are located between the surface and the
backrest of the vehicle´s seat.
2. Make sure the 5-point harness of the safety seat has been correctly installed
(see section 3).
3. Follow the steps described in section 3.8.
4. Rotate the seat by pulling the 360º turning device
(Q)
5. Make sure the ISOFIX arms are displayed to install the car seat.
6. Place the seat in the back seat of the vehicle.
7. Hold the safety seat with both hands and hook the two ISOFIX arms
into the vehicle seat ISOFIX connectors until they fasten with a click on both
sides. The red button will partially change to green on both sides (fig. 4.4).
8. Shake the seat to check that it is correctly anchored to the vehicle's ISOFIX points.
and the headrest at the same time. This
(fig. 4.2).
(L)
to position 3 (fig. 4.3)
(Q)
firmly
25