Black and Decker BDASB18 Traducción De Las Instrucciones Originales página 9

♦ For screwdriving, set the collar to the desired setting. If
you do not yet know the appropriate setting, proceed as
follows:
♦ Set the collar to the lowest torque setting.
♦ Tighten the first screw.
♦ If the clutch ratchets before the desired result is
achieved, increase the collar setting and continue
tightening the screw. Repeat until you reach the correct
setting. Use this setting for the remaining screws.
Keyless chuck (fig. F)
Warning! Make certain the lock-off button (2) is engaged
to prevent switch actuation before installing or removing
accessories.
To insert a drill bit or other accessory:
♦ Grasp the rear half of the chuck (4) with one hand
and use your other hand to rotate the front half in the
counterclockwise direction, as viewed from the chuck
end.
♦ Insert the bit or other accessory fully into the chuck, and
tighten securely by holding the rear half of the chuck and
rotating the front portion in the clockwise direction as
viewed from the chuck end.
Warning! Do not attempt to tighten drill bits (or any other
accessory) by gripping the front part of the chuck and turning
the tool on. Damage to the chuck and personal injury may
occur when changing accessories.
Dual range gearing (Figure G)
The dual range feature of your drill allows you to shift gears
for greater versatility. To select low speed, high torque
setting (position 1), turn tool off and permit to stop. Slide gear
shifter button (5) away from the chuck. To select the high
speed, low torque setting (position 2), turn tool off and permit
to stop.
Slide gear shifter button towards the chuck.
Note: Do not change gears when tool is running. If you are
having trouble changing gears, make sure that the dual
range gear button is either completely pushed forward or
completely pushed back.
Drilling/screwdriving
♦ Select forward or reverse rotation using the forward/
reverse slider (2).
♦ To switch the tool on, press the switch (1). The tool
speed depends on how far you press the switch.
♦ To switch the tool off, release the switch.
Hints for optimum use
Drilling
♦ Use sharp drill bits only.
(Original instructions)
♦ Support and secure work properly, as instructed in the
Safety Instructions.
♦ Use appropriate and required safety equipment, as
instructed in the Safety Instructions.
♦ Secure and maintain work area, as instructed in the
Safety Instructions.
♦ Run the drill very slowly, using light pressure, until the
hole is started enough to keep the drill bit from slipping
out of it.
♦ Apply pressure in a straight line with the bit. Use enough
pressure to keep the bit biting but not so much as to stall
the motor or deflect the bit.
♦ Hold the drill firmly with two hands to control its twisting
action.
♦ DO NOT CLICK THE TRIGGER OF A STALLED DRILL
OFF AND ON IN AN ATTEMPT TO START IT. DAMAGE
TO THE DRILL CAN RESULT.
♦ Minimize stalling on breakthrough by reducing pressure
and slowly drilling through the last part of the hole.
♦ Keep the motor running while pulling the bit out of
a drilled hole. This will help reduce jamming.
♦ Make sure switch turns drill on and off.
Drilling in wood
Holes in wood can be made with the same twist drill bits
used for metal or with spade bits. These bits should be sharp
and should be pulled out frequently when drilling to clear
chips from the flutes.
Drilling in metal
Use a cutting lubricant when drilling metals. The exceptions
are cast iron and brass which should be drilled dry. The
cutting lubricants that work best are sulfurized cutting oil or
lard oil.
Drilling in masonry
For drilling in masonry, set the collar (3) to the hammer
drilling position by aligning the symbol with the marking.
Slide the speed selector (5) towards the front of the tool (2nd
gear).
Screwdriving
♦ Always use the correct type and size of screwdriver bit.
♦ If screws are difficult to tighten, try applying a small
amount of washing liquid or soap as a lubricant.
♦ Always hold the tool and screwdriver bit in a straight line
with the screw
Troubleshooting
Problem Possible cause
Unit will not start. Battery pack not
charged.
ENGLISH
Possible solution
Check battery pack
charging requirements
9