Editing Operations On The Remote Control (9Pin Rec/Dv Slave) Screen - JVC BD-X200E Manual Del Usuario

Synchronous Recording

Editing Operations on the REMOTE CONTROL (9PIN REC/DV SLAVE) Screen

Contents of the REMOTE CONTROL (9PIN REC/DV SLAVE) Screen
When the REMOTE SELECT item of the REMOTE MENU screen is set to 9PIN (REC), the REMOTE CONTROL (9PIN REC)
screen is displayed on the monitor. When set to DV (SLAVE) the REMOTE CONTROL (DV SLAVE) screen is displayed. The
contents of both screens are the same.
A keyboard and mouse can be used as an alternative to the DVD recorder's buttons when using the REMOTE CONTROL (DV
SLAVE) screen.
Front panel : Select using the cursor buttons (t, 8, 7, and 6), and confirm the selection using the SET button.
: Select using the arrow keys (†, ©, √, and ∞), and confirm the selection using the Enter key.
Keyboard
Mouse : Left click the required button.
* Setting of the In Point, Out Point, and chapter points can only be carried out by keyboard input.
IN POINT (edit start point):
The time code of the position you want to start recording
(hour: minute: second: frame) is input from the keyboard.
EXIT:
Returns to the
original screen.
Chapter list:
This displays the time
codes of chapter
marks. These time
codes are displayed as
relative values with
respect to the In Point.
● The In Point's time
code is registered as
the first chapter point.
● A total of 98 chapters
can be setup.
● C H A P T E R
CREATION from the
RECORDER MENU
(2/2) screen must be
set to MANUAL for
this to be possible.
CHAPTER:
The right-hand field indicates
the current setting for
CHAPTER CREATION from
the RECORDER MENU (2/2)
screen.
● When set to MANUAL,
chapter marks can be
registered in this screen's
chapter list.
● When set to AUTO, the
DVD recorder's chapter
auto-create function will set
chapters. In such a case, it
will not be possible to
register chapters using this
screen's chapter list.
● Chapter
marks are
inserted at GOP intervals
(i.e., 15 frames). It will not
be possible to insert
chapter marks that are
closer together than this
interval.
E-74
All manuals and user guides at all-guides.com
REMOTE CONTROL SCREEN ( DV SLAVE )
EXIT IN POINT 00:00:00:00
: : : :
h m s h m
f
1 00:00:00:00 2 00:15:00:00
4 5
00:25:00:00 00:30:00:00
7 00:40:00:00 8 00:45:00:00
CHAPTER MANUAL
ADJ
BITRATE 8.0 Mbps
EDL
TC CANCEL
ADJUST:
This button can be
pressed to determine
the remaining disc time
based on the editing
time and also to set a
suitable bit rate. This
setting is then displayed
in the BIT RATE field.
OUT POINT (edit finish point):
The time code of the position you want to finish recording
(hour: minute: second: frame) is input from the keyboard.
00:10:00:00
OUT POINT
: : : : :
s h m s
f f
3 00:20:00:00
6
00:35:00:00
9 00:50:00:00
000 min
DISC REMAIN
FINALIZE
TC CANCEL : This button is used to remove setting values
for the In Point, Out Point, and chapter marks.
EDL : Calls up the EDL MANAGER screen. Edit lists
can be saved and read by operations on the
EDL MANAGER screen. (☞ Page 69)
Scrolls the chapter list.
DISC REMAIN:
This field shows an
estimate of the remaining
space for recording on the
disc.
FINALIZE:
This button is used to
finalize the disc.