Kärcher B 150 R Manual Del Usuario página 21

 Then correctly and completely charge
the batteries.
After the initial charge, the "V" to the right of
the battery indicator disappears.
Now the battery indicator works accurately.
Note:
If a battery type is selected in the battery
menu, the procedure described above
must be performed again. This is also the
case if the already set battery type is rese-
lected.
Battery display
The charge condition of the batteries is
shown on the display of the control panel.
The length of the bar indicates the
–
charge condition of the battery.
During the last 30 minutes the remaining
–
operating time is indicated in minutes.
Removing the batteries
 Bring the safety switch into the "0" position.
 For devices with a overhead guard, al-
ways observe the notes in the "over-
head guard" chapter.
Tilt the waste water tank backwards.
 Clamp off the minus pole of the battery.
 Clamp off the remaining cables from the
battery.
 Remove the batteries.
 Dispose of the used batteries according
to the local provisions.
Unloading
Note:
To take all functions out of operation imme-
diately, bring the safety switch into the "0"
position.
 Four floor boards of the pallet are fastened
with screws. Unscrew these boards.
 Place the boards on the edge of the pal-
let. Place the boards in such a way that
they lie in front of the four wheels of the
machine. Fasten the boards with
screws.
 Slide the four support beams included
in the packaging under the ramp.
 Remove the wooden bars in front of the
wheels.
1
2
1 Front brake lever (all unit models)
2 Rear brake lever (only unit model Adv)
 Pull the brake lever and insert a coin
between the lever and the brake.
Note:
The unit model Adv has a brake in the front
and rear. To push the device, both brakes
must be unlocked.
 Slowly push the machine down from the
ramp.
DANGER
Danger of accident due to lacking braking
effect.
 Remove the coin immediately after
pushing the device.
or
 Plug in the Intelligent Key.
 Bring the safety switch into the "1" posi-
tion.
 Set programme selector switch to trans-
port run.
 Set the travel direction switch to "for-
ward".
 Actuate the accelerator pedal.
 Drive the appliance off the pallet.
 Bring the safety switch into the "0" posi-
tion.
Install cleaning head
The procedure for changing the cleaning
head is described in the chapter "Mainte-
nance Tasks".
Note:
On some models, the cleaning head is al-
ready installed.
Installing the Brushes
The installation of the brushes is described
in the chapter "Maintenance Tasks".
Installing the Vacuum Bar
 Insert the vacuum bar into the vacuum
bar suspension in such a manner that
the profiled sheet is positioned above
the suspension.
 Tighten the wing nuts.
 Insert the suction hose.
Operation
DANGER
Risk of injuries. Never use the unit without
protective roof in areas where the opera-
tors can be hit by dropping objects.
Note:
To take all functions out of operation imme-
diately, bring the safety switch into the "0"
position.
5
-
EN
Adjusting driver's seat
 Operate the lever for the seat adjust-
ment and move the seat to the desired
position.
 Release the seat adjustment lever and
lock the seat in place.
Turning on the Appliance
 Take the seating position.
 Plug in the Intelligent Key.
 Bring the safety switch into the "1" position.
 Turn the programme switch to the de-
sired function.
 If the relevant indication appears on the
display, perform the maintenance task.
Display Activity
Maintenance Clean the vacuum bar.
Vacuum bar
Maintenance Clean the fresh water fil-
Fresh water Fil- ter.
ter
Maintenance Check vacuum lips for set-
Suction lip ting and wear and tear.
Maintenance Clean protective turbine
Turbine strainer strainer.
Maintenance Check brush for wear and
Brush head tear and clean it.
 Press Info button.
 Reset the counter for the corresponding
maintenance (see "Care and mainte-
nance/resetting counter").
Note:
If the counter is not reset, the maintenance
indicator appears again with every start-up
of the device.
Switching on the light
Daytime running light
The daytime running light is in operation
when the device is switched on.
Work light (option)
 Set programme selector switch to trans-
port run.
 Press Info button.
 Turn the info button until "Switch menu"
is displayed.
 Press Info button.
 Turn the info button until "Work light" is
highlighted.
 Press Info button.
Check parking brake
DANGER
Risk of accident. Prior to every operation,
the parking brake must be checked for
proper function on a level ground.
 Turn on the appliance.
 Set the travel direction switch to "for-
ward".
 Set programme selector switch to trans-
port run.
 Gently depress drive pedal.
 The brake must unlock audibly. The ma-
chine must roll easily on a plane surface.
When the pedal is released, the brake locks
audibly. Switch off the machine and call the
aftersales service if the above-mentioned
events do not occur.
21