Publicidad
Idiomas disponibles
Idiomas disponibles
Controls and Electrics
YOU MUST:
•
Connect the Control Box (key 26) either directly to the battery or to a primary distribu-
tion board with sufficient spare amperage capacity.
•
Keep the total length of both the positive and negative wires to a minimum, selecting
your wire size from the Electrical Specifications table below.
Caution! Inadequate wire size will result in voltage drop, and will
reduce performance.
•
Make all joints with appropriately rated marine grade terminal blocks and crimp
connectors.
•
Use marine grade multi-strand copper wire.
•
Support all wires approximately every 18" (46 cm) with plastic cable clips.
YOU MUST FIT the correct size of fuseholder or circuit breaker, selected from the Electrical
Specifications table. If you connect the Control Box directly to the battery, fit your fuseholder
or circuit breaker within 7" (17cm) of the battery.
Caution! Remove fuse, or turn circuit breaker off, whilst installing
Controls and Electrics.
•
Fix the Control Box (key 26) in a dry but accessible position close to the Flush pump.
•
Select a position for the Control Panel (key 26) that is convenient for both standing and
seated users, and which allows you to run the 10ft (3m) control cable out of sight to the
Control Box.
•
To use the Jabsco fascia panel provided, (Key 29) drill a 5/8" (16mm) hole for the 6 way
control cable connector. Screw the control panel (key 28) onto selected location with
suitable counter sunk head screws. Clip on fascia panel (key 29)
To use Gewiss fascia panels remove the four screws tabs (see picture below). Cut a
•
rectangular hole 53mm x 92mm. Fix panel to selected location with four counter sunk
head screws. Clip on Gewiss fascia panel
•
To use Vimar fascia panels remove the four screw tabs (see picture below) Cut a rectan-
gular hole 53mm x 92mm. Place adaptor (key 30) onto panel (key 28) and screw into
place with four counter sunk head screw. Clip on Vimar panel onto adaptor.
Cut along indented lines on either
side and pull off screw tabs
•
Slide the Heat Shrink Sleeve (key 27) over the control cable. Plug in the 6 way control
cable to the Control Box, and carefully use a hot air gun or hairdryer to seal the Heat
Shrink Sleeve over the 6 way connector.
•
Note that the Control Box has 6 other leads - Red and Black, Orange and Blue and 2
black ground wires.
•
Connect your boat's Positive (+) feed to the Red (+) input lead of the Control Box, and
your boat's Negative (−) return to the Black (−) output lead of the Control Box.
•
Connect the Orange (+) output lead of the Control Box to the Red (+) input lead of the
Flush pump motor (key 21).
•
Either connect the Blue (+) output lead of the Control Box to any terminal of the Sole-
noid Valve (key 31) or to the Red (+) input lead of the Raw Water Rinse pump (key 32).
•
Connect 1 black ground wire to the remaining terminal on the solenoid valve or the
black wire on the raw water rinse pump.
•
Connect the other black wire to the black wire on the Flush pump
Screw into place with four
counter sunk head screws
To black wire on
macerator
Black wire to
negative battery
terminal
Red wire to
positive battery
terminal
Control box
Electrical Specifications
Fuse/
Voltage
Amp Draw
Breaker
12 Vdc
20
25 amp
24 Vdc
10
15 amp
* Wire length is the total distance from the battery to the Flush pump and back to the battery
Securing the bowl and fitting the seat and lid
•
Apply a bead of white silicone sealant to the base of the toilet.
•
Bolt down the toilet, using plastic washers next to the china, with stainless steel wash-
ers between the plastic washers and the bolt heads. Tighten the fastenings securely. If
you are not using self-locking nuts, use nutlocking compound.
•
Fit the seat and lid using the adjustable fastenings supplied with it.
Testing
•
Ensure that the battery is fully charged, and that the circuits are live.
•
Open both seacocks.
•
Refer to the next section - OPERATING INSTRUCTIONS.
•
To prime the Solenoid Valve or Rinse pump on first installation, operate the 'Quick Flush'
function several times until water flows into the toilet bowl. Thereafter they are automatically
switched by the Control Panel.
Safety
Ensure that this INSTRUCTION MANUAL reaches the owner, skipper or operator of the craft as
it contains essential safety information.
ON COMPLETION - CLOSE BOTH SEACOCKS
OPERATING INSTRUCTIONS
The toilet is one of the most used pieces of equipment on your boat.
Correct operation of the toilet is essential for the safety and comfort of
your crew and craft.
•
Open inlet and outlet seacock (and secondary valves if fitted)
•
Use Touch Pad Controller as described on Page 2.
•
Use good quality hard or soft household toilet paper, but do not
use more than necessary.
•
Do not put anything in the toilet unless you have eaten it first,
except toilet paper.
5
From macerator
on toilet
OR
To red wire on
toilet macerator
To black wire on
(Blue)
pump or second
terminal of solenoid
Wire size AWG (mm²) per foot (metre) of length*
0-20ft
20-30ft
30-50ft
(0-6m)
(6-9m)
(9-15m)
#14
#12
#10
(2. 5mm²)
(4 mm²)
(6 mm²)
#16
#16
#14
(1.5mm²)
(1.5mm²)
(2.5mm²)
To control pad
50-80ft
(15-24m)
#8
(10mm²)
#12
(4 mm²)
Publicidad
