Publicidad
Idiomas disponibles
Idiomas disponibles
Caution! Do NOT allow anything at all to touch or fall onto the mating
faces of the new ceramic seal!
•
Take the stationary half of the new seal (white ceramic face in rubber cup) and, with
rubber cup at the bottom, press it into the seal housing in the lower pump body (Key
20) using your clean, dry fingers only, leaving white ceramic face exposed.
•
Carefully slide the rotating half of the ceramic seal (black carbon face) down the motor
shaft to cover the white ceramic face.
•
Replace impeller on motor shaft. Fit washer and left hand nut.
Re-assemble pump
•
Place joint ring (key 15) in position.
•
Re-fasten the upper pump body (key 14) to the lower pump body (key 20), using the 7
screws (key 11 & 12) and nuts (key 13).
Refit pump assembly
•
Reconnect the Flush pump positive and negative motor leads. Offer up the complete
pump and hoses assembly to the bowl and to the bowl outlet.
•
Re-fasten the motor to the support block (key 6), using a new support strap (key 5).
•
Re-fasten the inlet hose (key 9) to the bowl outlet, with the hose clamp (Key 10), using
a new support strap (key 4).
Re-assemble non-return valve assembly.
•
Hoses
•
Examine all hoses throughout their length for chafe, kinks and splits under hose
clamps. Check all hose clamps for corrosion and replace worn or damaged parts.
Caution! Do not apply flame to the hose. Do not apply flame or heat to
the plastic hose tails on the toilet, rinse pump or solenoid valve. Do not
use oils, greases or synthetic lubricants. Do not apply sealing compounds
to any hose connections. Do not over tighten hose clamps. Any of these
actions may result in cracking or breakage of the plastic parts.
Reconnect all loose hose ends and secure them with their hose clamps.
•
Servicing - Testing
•
Open inlet and outlet seacocks (and secondary valves if fitted).
•
Switch on power or replace fuse.
•
Use Touch Pad Controller as described on page 2, to check all functions, and then
inspect for leaks.
ON COMPLETION - CLOSE BOTH SEACOCKS!
SPARE PARTS
PIÈCES DE RECHANGE / ERSATZTEILE / PEZZI DI RICAMBIO
RESERVEONDERDELEN / RESERVDELAR / PIEZAS DE REPUESTO
Service Kits Availible
Kit
Part No.
A
58100-2000
58103-1012
B
58103-1024
C
58029-1000
58039-1000
Description
Major Service Kit
Pump Assembly, 12v
Pump Assembly, 24v
Control Kit
Hose Kit (key 9 & 22)
7
Key
Description
1
Seat & Lid, Set
Seat & Lid Set, Soft Close
2
Hinge Kit, Pair
2a
Hinge Kit, Pair (Soft Close)
3
Rinse Intake Seal & Elbow
4
Support Strap, Discharge Hose
5
Support Strap, Motor
6
Support Strap, Motor
14" Bowl, Angled Back
14" Bowl, Vertical Back
7
17" Bowl, Angled Back
17" Bowl Vertical Back
8
Hose Clip, Large
9
Inlet Hose, Flush Pump
10
Hose Clip, Medium
11
Screw, Long
12
Screw, Short
13
Nut
14
Pump Body, Upper
15
Ring Seal
16
Nut
17
Washer
18
Impeller
19
Ceramic Seal
20
Pump Body, Lower
Motor 12v
21
Motor 24v
22
Outlet Hose, Pump
23
Clip, Small
24
Non - Return Valve Assembly
25
Joker Valve
26
Control box, electronics
27
Heat Shrink Sleeve, Control Cable
28
Panel
29
Jabsco White Fascia Panel
30
Adaptor Plate
Solenoid Valve, 12v
31
Solenoid Valve, 24v
Rinse Pump, 12v
32
Rinse Pump, 24v
33
Pump Guard
Qty per Service Kit
Qty per
Part No.
Toilet
A
B
1
58104-1000
1
58104-2000
1
58105-1000
1
58105-3000
1
58107-1000
1
See Kits
1
1
1
See Kits
1
1
1
See Kits
1
1
1
58048-1000
1
58068-1000
1
58028-1000
1
58038-1000
1
See Kits
1
1
1
See Kits
1
1
1
See Kits
1
1
4
See Kits
1
4
3
See Kits
1
3
7
See Kits
2
7
1
See Kits
1
1
See Kits
1
1
1
See Kits
1
1
1
See Kits
1
1
1
See Kits
1
1
See Kits
1
1
1
See Kits
1
1
See Kits
1
1
See Kits
1
1
See Kits
1
1
2
See Kits
2
2
1
58109-1000
1
29092-1000
1
See Kits
1
See Kits
1
See Kits
1
See Kits
1
See Kits
1
37038-2012
1
37038-2024
1
31331-0092
1
31331-0094
1
46400-9500
C
1
1
1
1
1
Publicidad
