Key Automation ALT3KF Instrucciones Y Advertencias Para Su Instalación Y Uso página 41

SAFETY AND CONTROL DEVICE CONNECTORS
24 VAC Accessories power supply 24 Vac without regulation. With battery operation output not active
24 VAC Accessories power supply 24 Vac without regulation. With battery operation output not active
COM Common for the FLASH-IND-LED outputs
FLASH Flashing light output 24Vdc (without regulation), maximum 15W
IND output for barrier open indicator light 24 Vdc not regulated 5W MAX / Electric lock output 12Vac, 15VA maximum
IND/ELEC
selectable with parameter
LED Courtesy light output 24Vdc (without regulation), maximum 15W, controllable also via radio ON-OFF command
NEG Photocell power supply negative
PH-POW
Photocells PH1 and PH2 power supply positive; phototest can be selected with parameter
EDGE safety device, NC contact between EDGE and EDGE (warning, with dip switch 1 ON the safety device input is
off). This input is classified as a safety device; the contact can be deactivated at any time, cutting out the automation
EDGE STOP system and disabling all functions, including Automatic Closure.
Safety sensor edge, ON/OFF, NC contact or resistive 8K2 between EDGE and EDGE.
Input selectable with parameter
Photocells (opening), NC contact between PH2 and COM (warning, with dip switch 2 ON the PHOTOCELL 2 safety
PH2 device input is off). The photocell is tripped at any time during opening of the automation system, halting operation
immediately; the automation will be reversing depending of the
Photocells (closing), NC contact between PH1 and COM (warning, with dip switch 3 ON the PHOTOCELL 1 safety
PH1 device input is off) The photocell is tripped at any time during closing of the automation system, halting operation im-
mediately and reversing the travel direction
OPEN command NO contact between OPEN and COM
OPEN
Contact for the HOLD-TO-RUN function. The barrier OPENS as long as the contact is held down
CLOSE command NO contact between CLOSE and COM
CLOSE
Contact for the HOLD-TO-RUN function. The barrier CLOSES as long as the contact is held down
PARTIAL command NO contact between PAR and COM
PAR
Used to open the barrier partially, depending on the software setting (not active up-and-over door)
STEPPING command NO contact between SBS and COM
SBS
Open/Stop/Close/Stop command, or as set in the software
COM Common for the PH2-PH1-OPEN-CLOSE-PAR-SBS inputs
SHIELD Antenna - shield
ANT Antenna - signal
6.5 - Disabling the safety devices
EDGE
The inputs of the safety EDGE must be connected to the EDGE
and EDGE terminals. To bypass the safety edge, move the
left-hand dip switch upwards. After having activated the dip
switch, the EDGE LED starts to flash at a fast rate.
ATTENTION ! CONFIRM EDGE INPUT DEACTIVATION
BY PRESSING AND
AND HOLDING THEM DOWN UNTIL THE EDGE LED STOPS
FLASHING.
PHOTO 2
The PHOTO2 contact must be connected to the COM and PH
2 terminals. To bypass the photocell, move the middle dip
switch upwards. After having activated the dip switch, the
PH2 LED starts to flash at a fast rate.
6.6 - Display during normal operation
In "NORMAL OPERATING MODE", i.e. when the system is powered up normally, the 5digit LCD display shows the following messages
(to compare with the previous electronic board CT10224 check the second column):
CT10324 OLD CT10224
'
BUTTONS SIMULTANEOUSLY
MEANING
Learning not done
--
Barrier closed or switch-on after shutdown
OP
Barrier opening
CL
Barrier closing
.
ATTENTION !
BY PRESSING THE
AND HOLDING THEM DOWN UNTIL THE PH2 LED STOPS
FLASHING.
PHOTO 1
The PHOTO1 contact must be connected to the COM and PH 1
terminals. To bypass the photocell, move the right-hand dip
switch upwards. After having activated the dip switch, the
PH1 LED starts to flash at a fast rate.
ATTENTION !
BY PRESSING THE
LY AND HOLDING THEM DOWN UNTIL THE PH1 LED STOPS
FLASHING.
24 Vdc, 200 mA
parameter
CONFIRM PH2 INPUT DEACTIVATION
AND BUTTONS SIMULTANEOUSLY
ACONFIRM PH1 INPUT DEACTIVATION
AND BUTTONS SIMULTANEOUS-
EN
41