Publicidad
Idiomas disponibles
Idiomas disponibles
To do a check of the muffler
WARNING:
face may contain deposits of combustion
particles on the surfaces that may be
carcinogenic.
•
Always wear personal protective
equipment when you do a check of
the muffler to prevent skin touch and
inhalation of the dangerous particles.
•
Make sure that there is a sufficient air
flow in the area when you clean and/or
do maintenance on the muffler.
•
Do not not use pressurized air to clean
the muffler.
•
Clean the muffler with a steel brush and
brush away from your body.
•
Examine the muffler regularly to make sure that it is
attached correctly and not damaged.
Hydraulic safety
WARNING:
instructions that follow before you use the
product.
•
Make sure that the hydraulic hose connections are
tight and that there is no oil leakage.
•
Be careful when you tighten the hydraulic
connections. If you tighten the hydraulic connections
too much, it can cause damage to the O-rings.
•
Make sure that the hydraulic hose connections are
clean and in good condition.
•
Pressurized hydraulic oil is dangerous and can
cause serious injury. Do not look for an oil leakage
when the hydraulic system is pressurized.
•
Be careful when you fill the product with hydraulic oil.
The hydraulic oil is flammable. If you spill hydraulic
oil, clean the surface.
•
Only fill the product with hydraulic oil in a location
with good airflow.
Safety instructions for maintenance
WARNING:
instructions that follow before you use the
product.
•
Use personal protective equipment. Refer to
Personal protective equipment on page 7 .
•
Only do the maintenance as given in this operator's
manual. Let an approved service agent do all other
servicing.
•
Refer to the service manual of the engine for
safe operation and maintenance. Save the service
manual for further reference.
10
A used muffler/mounting
Read the warning
Read the warning
•
If the maintenance is not done correctly and
regularly, the risk of injury and damage to the
product increases. Let the machine cool off before
you do any maintenance or inspections. Take out the
ignition key.
•
Let the product become cool before you do any
maintenance or inspections. Make sure that there is
no risk of accidental start.
•
Clean the product to remove dangerous material
before you do the maintenance.
•
Do the maintenance of the product on stable level
ground. Make sure that the product cannot move.
•
Do not make modifications to the product.
Modifications that are not approved by the
manufacturer can cause serious injury or death.
•
Replace damaged, worn or broken parts.
•
Do not use a pressure washer to clean the product.
•
Only use lint-free cleaning cloths.
•
Always use original accessories and spare parts.
Accessories and spare parts that are not approved
by the manufacturer, can cause serious injury or
death.
•
After maintenance, do a check of the vibration level
in the product. If it is not correct, speak to an
approved service agent.
•
Do not use a product that is damaged or does
not operate correctly. Do the safety checks,
maintenance and the servicing as given in this
manual. All other maintenance work must be done
by an approved service agent.
•
Product related accidents occur during the
troubleshooting, servicing and maintenance as the
operator must be in the risk area of the product. The
operator must be careful and prepare the work to
prevent accidents.
•
Do not make a hole in the HEPA filter. A broken
HEPA filter can cause dust to release into the air.
•
Make sure that you obey all local regulations to
dispose the dangerous dust correctly, before and
during maintenance.
•
Make sure that you obey all local regulations to
dispose all replaced parts after the servicing.
•
Do not use a product that is damaged or does
not operate correctly. Do the safety checks,
maintenance and the servicing as given in this
manual. All other maintenance work must be done
by an approved service agent.
•
Only let an approved electrician do all checks of the
electric components.
•
Be careful when you handle the filters. If you
damage the filters, there is a risk of dust dispersion.
•
The manufacturer, or an instructed person, must
do a technical inspection at least annually. The
technical inspection includes an inspection of the
filters for damage, air tightness of the product and
correct function of the control mechanism. In addition
the filtration efficiency of the product must be tested
at least annually, or more frequently as may be
specified by national requirements. If the test is not
2291 - 001 - 17.05.2024
Publicidad
