The Service Setting 2 Menu - Sony VPH-G90E Manual De Instalación

NORMAL DEFOCUS MODE
Selects if the projector performs defocusing during
projection.
S I N P U T - A
S C R E E N T Y P E :
SET
SETTING2
S C R E E N B
A B G M O D E : O N
INPUT
INFO. N O R M A L D E F O C U S
M O D E : O N
SET
INFO 5 B N C M O D E : O F F
SERVICE
SETTING1
SERVICE
SETTING2
SEL: SET: ENTER EXIT: MENU
ON: Normally set to this position. Just focusing is
applied during the magnetic focus adjustment, and
defocusing is applied when you exit from the
magnetic focus adjustment mode.
OFF: Just focusing is applied even during projection.
Note
During the registration adjustment, just focusing is
applied regardless of this setting.
5BNC MODE
Set to ON when you connect the MONITOR OUT
connector on the PC-1271/1271M Signal Interface
Switcher (not supplied) to the INPUT A connectors
with the 5BNC cables.
S I N P U T - A
S C R E E N T Y P E :
SET
SETTING2 S C R E E N B
A B G M O D E : O N
INPUT
INFO. N O R M A L D E F O C U S
M O D E : O N
SET
INFO 5 B N C M O D E : O F F
SERVICE
SETTING1
SERVICE
SETTING2
SEL: SET: ENTER
EXIT: MENU

The SERVICE SETTING 2 Menu

(Service/Expert modes)
The SERVICE SETTING 2 menu is used for the
adjustments performed by the service personnel.
S
D I R E C T P O W E R O N : O F F
SET
SETTING2 O N D E L A Y : O F F
A L L W H I T E M O D E : 2 0 m i n
INPUT
INFO. P J C O M : 3 8 . 4 K
R S - 2 3 2 C / 4 2 2 A : 3 8 . 4 K
SET
INFO
SERVICE
SETTING1
SERVICE
SETTING2
SEL: SET: ENTER
DIRECT POWER ON
Set to ON to turn on the projector by pressing the
MAIN POWER switch on the projector. Set to OFF to
enter standby mode by pressing the MAIN POWER
switch.
S I N P U T - A
D I R E C T P O W E R O N : O F F
SET
SETTING2
O N D E L A Y : O F F
A L L W H I T E M O D E :
INPUT
INFO. 2 0 m i n
P J C O M : 3 8 . 4 K
SET
INFO R S - 2 3 2 C / 4 2 2 A : 3 8 . 4 K
SERVICE
SETTING1
SERVICE
SETTING2
SEL: SET: ENTER EXIT: MENU
Note
When the projector is in standby mode with DIRECT
POWER ON set to ON, the projector will be turned on
automatically if the power interruption occured and
has been restored.
ON DELAY
When connecting multiple projectors, set to ON to turn
on the projectors sequencially one by one.
S I N P U T - A
D I R E C T P O W E R O N : O F F
SET
SETTING2
O N D E L A Y : O F F
A L L W H I T E M O D E :
INPUT
INFO.
2 0 m i n
P J C O M : 3 8 . 4 K
SET
INFO
R S - 2 3 2 C / 4 2 2 A : 3 8 . 4 K
SERVICE
SETTING1
SERVICE
SETTING2
SEL: SET: ENTER
EXIT: MENU
The projectors are turned on in the numerical order of
the device index numbers.
I N P U T - A
EXIT: MENU
69
Before adjustment (GB)