3M 5908556 Manual Del Usario página 10

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

 Cable and Cable Tension:
Inspect the cable for corrosion, kinks or damage that will aff ect strength and impede the cable sleeve from traveling
on the cable. If there are any nicks or kinks in the ladder cable, the cable must be inspected by a competent person
prior to use. Inspect for signs of abrasion against the ladder or structure. Replace the cable if defects are found.
Inspect for proper tension. Groove should be exposed above bottom template. (See Figure 16 E.) You should not be
able to pull tension rod down by hand. Cable should be tight enough to prevent contact with the ladder/structure.
Re-tension the cable if necessary. Do not over-tension the system.
 Installation and Service Label:
Inspect the installation and service label. The label should be securely attached and fully legible. The installation
date, installed by, maximum users per system and system length should be clearly marked on the label. Record the
inspection date on the label after this inspection is completed.
 Ladder/Climbing Structure:
Inspect the ladder/climbing structure to which the Lad-Saf
condition, secure, and safe to climb. DO NOT USE if the condition of the structure is questionable. Consult
instructions and/or personnel familiar with the structure prior to use.
5.5
RFID TAG:
The Lad-Saf
system and the Lad-Saf
(Figure 2, Item N & Figure 11, Item 11). The RFID tag can be used in conjunction with a handheld reading device and
web based portal to simplify inspection and inventory control and provide records for your fall protection equipment.
If you are a fi rst-time user, contact a 3M Fall Protection Customer Service representative (see back cover), If you have
already registered, follow the instructions provided with your handheld reader or on the 3M web portal to transfer your
data to your web log.
6.0 MAINTENANCE, SERVICING, STORAGE
6.1
See section 5.0 for inspection related maintenance issues. If the carrier cable becomes heavily soiled with oil, grease, paint, or other
substances, clean it with warm soapy water. Wipe off the cable with a clean, dry cloth. Do not force dry with heat. Do not use
acid or caustic chemicals that could damage the cable.
Additional maintenance and servicing procedures must be completed by an authorized service center. Authorization must
be in writing.
The Lad-Saf
X3 Detachable Cable Sleeve may be cleaned with warm, soapy water. After sleeve has been cleaned, the
device may be lubricated with a light machine oil in select areas. A small amount of lubrication can be applied to pivot
points (G) or at the base of (C), see Figure 2.
Store the Lad-Saf
where chemicals vapors exist. Thoroughly inspect the sleeve after extended storage.
Transport the Lad-Saf
overheated or refrigerated atmospheres.
7.0 SPECIFICATIONS
7.1
All top and bottom brackets, cable guides, carrier cable, and fasteners are made of galvanized or stainless steel. Contact
3M Fall Protection for material specifi cation details if required. The LAD-SAF™ system, when installed according to the
installation instructions, meets OSHA 1910.140, OSHA 1926.1053, OSHA 1910.29, OSHA 1926.502, ANSI Z359.16, CSA
(Z259.2.5) and CE (EN353-1:2014+A1:2017) requirements.
Declaration of Compliance: www.3M.com/FallProtection/DOC
X3 Detachable Cable Sleeve include a Radio Frequency Identifi cation (RFID) tag
X3 Detachable Cable Sleeve in a cool, dry, clean environment, out of direct sunlight. Avoid areas
system in an enclosure to protect it from any cuts, moisture or ultraviolet light. Avoid corrosive,
system is attached. Make sure the structure is in good
10

Publicidad

Tabla de contenido
loading

Tabla de contenido