diversey TASKI swingoBot 2000 Manual De Instrucciones página 76

Brush installation
Notice:
When the front door is opened, the power
supply to the brush unit is capped.
Before inserting, please ensure
• that the brush does not fall below the red marking (bristles)
or 1cm of bristle length.
• the pad for wear and cleanliness before use.
Attention:
Do not use brushes which have reached
their wear limit. The wear limit is indicated
by the length of the red bristle. Do not use
worn or contaminated pads. Use original
TASKI brushes only. Failure to observe
these instructions may result in inade-
quate cleaning results or even floor dam-
age.
• Push the front door release upwards and open the front
door.
• Place the brush under the brush holder so that the locating
bolts fit into the recesses provided, push the brush up-
wards and turn it briefly counterclockwise until it clicks into
place.
• Close the front door.. Ensure that the front door latches
correctly.
Insert suction nozzle / squeegee
Notice:
The suction nozzle / squeegee must be
correctly inserted and secured.
The suction nozzle / squeegee can other-
wise become detached from the holder
and cause damage to the machine and
ground.
• Pull the suction nozzle lock outwards. You will find the suc-
tion nozzle lock on the lower left side of the machine.
• Take the suction nozzles and place them with the position-
ing bolt in the recess provided.
• Push the suction nozzle upwards and push it until the suc-
tion nozzle is in the correct position or until the small lock-
ing bolt fits into the recess provided.
• Push the suction nozzle briefly upwards again until the
locking bolt fits into the recess.
• Push the release lever back into position to lock/fix the suc-
tion nozzle.
Filling the fresh water tank
Attention:
The front door must be closed so as to pre-
vent splashing water from getting to the
electronics of the brush units.
Attention:
Max. permissible water temperature
60 °C/140 °F.
Diversey recommends using cold water,
as hot water will adjust to the ground tem-
perature as soon as it comes into contact
with the ground. Thus there are no advan-
tages to using hot water.
74
Notice:
The fresh water tank can be filled using a
water hose. The maximum filling level indi-
cator is located on the outside of the ma-
chine.
• The machine must be switched off.
• Open the tank lid. To do this, pull on the tank cover release.
• Carefully tilt the tank backwards until it is lying on the ma-
chine.
• Remove the dosing cup and the dirt strainer from the fresh
water tank.
• Fill the fresh water tank with water.
• Remove the dosage cup and the dirt sieve from the fresh
water tank.
• Tip the tank cover back into its original position and press
it down until it locks.
Fill fresh water tank with Aquastop-System
Notice:
This machine is equipped with a filling sys-
tem.
Connect the water hose from the tap with
the Aquastop-System.
The Aquastop-System automatically stops
the supply of water when the maximum fill-
ing level has been reached.
Dosing
Attention:
Wear gloves, goggles and appropriate
(protective) working clothes when han-
dling chemical products!
Notice:
Use chemical products recommended by
Diversey only and always observe the
product information.
Caution:
Using unsuitable products (e.g. products
containing chlorine, acids or solvents) may
cause harm to health and severe damage
to the machine.
Notice:
An automatic dosage (IntelliDose) is inte-
grated into this machine. You can find out
how to exactly operate the IntelliDose in
the corresponding instructions for use.
Notice:
Diversey recommends sustainable work-
ing by determination of the correct product
dosing quantity. Overdosing or underdos-
ing will lead to unsatisfactory cleaning re-
sults.