Technical Data - Kärcher B 110 R Manual De Instrucciones

Malfunction
The water volume is insuf-
ficient
The suction performance
is too low
The cleaning results are
unsatisfactory
The brushes do not rotate 1. Reduce the contact pressure.
The device does not brake 1. Undo the brake lock (see "Operation / Pushing the device").
The waste water drain
hose is clogged
The "Dose" detergent dos-
ing unit does not work
Allgemein
Driving / cleaning speed
Transport speed
Travel speed, backwards
Theoretical surface performance
Theoretical surface coverage with side scrub-
bing deck
Practical surface coverage
Fresh water tank volume
Waste water tank volume
Coarse dirt container volume
Volume of detergent tank (Dose option)
Detergent dosing unit
Water dosing
Rectification
1. Check the fresh water filling level, if necessary fill the tank completely so that the air is
pressed out.
2. Remove and clean the fresh water filter.
3. Insert the filter and screw on the cap.
4. Only with R cleaning head: Pull off the water distribution strip on the cleaning head.
5. Only with R cleaning head: Clean the water channel.
6. Check the hoses for clogging and clean if necessary.
1. Clean the seals between the waste water tank and the cover, check for leaks and replace
if necessary.
2. Check the fluff filter for contamination and clean if necessary.
3. Clean the suction lips at the suction bar, turn over or replace if necessary.
4. Close the lid on the waste water drain hose.
5. Close the cover of the waste water tank rinsing system.
6. Check the suction hose for clogging and clean if necessary.
7. Check the suction hose for leaks and replace if necessary.
8. Check the adjustment of the suction bar.
1. Set the appropriate cleaning program for the cleaning task.
2. Use suitable brushes for the cleaning task.
3. Use a suitable detergent for the cleaning task.
4. Reduce the driving speed.
5. Adjust the contact pressure.
6. Adjust the squeegee blades.
7. Check the brushes for wear and tear and replace if necessary.
8. Check the water output.
2. Check if the brushes are blocked by a foreign body and remove the foreign body if nec-
essary.
3. If the motor is overloaded, let the motor cool down.
4. Set the program switch to "OFF".
5. Wait 10 seconds.
6. Set the program switch to the desired program.
7. Check that the plug of the device is plugged into the cleaning head.
1. Open the dosing unit cover at the drain hose.
2. Pull the suction hose off the suction bar and close it by hand.
3. Set the program switch to "Vacuum".
The blockage is sucked out of the drain hose into the waste water tank.
1. "Dose" version only: Call Customer Service.

Technical data

km/h
km/h
km/h
2
ft /h (m
h)
2
ft /h (m
h)
2
ft /h (m
h)
gal (l)
gal (l)
gal (l)
gal (l)
%
gpm (l/
min)
B 110 R 65 B 110 D 65
6 6
6 6
4 4
2
/ 41979 (3900) 41979 (3500) 48438 (4500) 48438 (4500)
2
/ - -
2
/ 29385 (2730) 29385 (2730) 33906 (3150) 33906 (3150)
29 (110) 29 (110)
29 (110) 29 (110)
0,4 (1,6) -
1,3 (5) 1,3 (5)
0,25...3 0,25...3
0,04...1,5 0,04...1,5
(0,15...5,7) (0,15...5,7)
English
B 110 R 75 B 110 D 75
6 6
6 6
4 4
54896 (5100) 54896 (5100)
29 (110) 29 (110)
29 (110) 29 (110)
0,5 (1,8) -
1,3 (5) 1,3 (5)
0,25...3 0,25...3
0,04...1,5 0,04...1,5
(0,15...5,7) (0,5...5,7)
23