General Cleaning - Moretti Forni Neapolis 6 Manual De Instrucciones

THE FOLLOWING
MAINTENANCE" ARE STRICTLY RESERVED TO SPECIALIST TECHNICIANS
WITH THE RELEVANT LICENSE AS WELL AS BEING APPROVED BY THE
MANUFACTURER.
5 SPECIAL MAINTENANCE
5.1 PRELIMINARY SAFETY OPERATIONS
WARNING!
All maintenance operations and repairs must
be carried out using suitable accident prevention equipment, by
specialised and properly licensed technicians, approved by the
manufacturer.
Before performing any maintenance operation, disconnect the
power supply by turning off the switches fitted on the outside of the
oven and/or the leavening compartment and wait for the appliance
to cool to room temperature.
All precautions are of importance to ensure that the oven remains in
a good state, and failure to observe them may result in serious
damage which will not be covered by the warranty and may lead to
hazard exposure
WARNING!
If the oven needs to be moved, first lift the 2
tilting casings on the sides (fig.5, item F) and RELEASE THE
BRAKES ON THE 2 FRONT WHEELS OF THE CELL, pushing
the release tabs (fig 4E GO item) with a screwdriver. Once in place,
engage the brakes.
WARNING!
Periodically (at least once a year), and every
time problems occur during operation, the state of the oven must be
checked by a specialist technician, who needs to look at the condition
of the oven and inspect inside the electric panel and the steam pipe,
cleaning any dust away. Also access all removable compartments,
side, top, front, and rear, and carefully clean out any dust or flour
deposits inside.
5.2

GENERAL CLEANING

After carrying out the operations described in point 5.1 above, clean the
appliance as follows.
Regularly clean the appliance in general.
NOTE:
To clean the baking surface, use the CLEANING
FUNCTION by thermo-reduction (point 3.2.2 section M) or use
delicately a suitably long soft brush. IT IS STRICTLY
FORBIDDEN TO WET THE BAKING SURFACE EVEN WITH A
DAMP CLOTH, BECAUSE THIS MAY IRREPARABLY
DAMAGES THE BISCUIT-WARE.
IT IS PROHIBITED TO STRIKE THE BISCUIT SHELF WITH
THE PEEL AS THIS WILL CAUSE IT TO BREAK.
NOTE:
Be careful not to hit the side/rear refractories, any
impact could break them; if this happens, the functionality of the
oven is not compromised; any cracks in Biscuit-wares may occur but
they do not compromise the functionality of the oven.
After leaving the appliance to cool down, carefully remove, from internal
and external parts, except from the biscuit-ware, all the residues that
might have collected during cooking, using a damp sponge with a little
soapy water, if necessary. Rinse and dry the areas, being sure to wipe
parts with satin finish in the direction of the finish.
WARNING!
Carefully clean off regularly any fat or grease
that may have dripped during cooking as this is a potential fire
hazard.
WARNING!
Based on the use of the appliance it will be appropriate to remove
periodically the biscuit-ware elements as described in point 5.3.5 and
remove from underneath them all the baking residues.
WARNING!
Never clean the appliance with direct jets of
water or with pressurised water jets. Always take care to ensure that
the water or other products use does not come into contact with
electrical parts.
The use of toxic or harmful detergents is strictly prohibited.
WARNING
INSTRUCTIONS,
UK9
WHICH CONCERN
NOTE:
Do not use solvents, detergents containing aggressive
substances (chlorides, acids, corrosives, abrasives, etc. ...) or
equipment that could damage surfaces. Before starting up the
appliance again, make sure that none of the cleaning equipment has
been left inside.
5.3 REPLACING PARTS OF THE BAKING CHAMBER
5.3.1 REPLACING THE LIGHT BULB
Given the heavy workload to which the light bulbs are subjected, in time
it may be necessary to replace them.
NOTE:
THE NEW
TEMPERATURE LIGHT BULB AND SHOULD NOT BE
TOUCHED WITH BARE HANDS, BUT WITH GLOVES OR A
CLOTH IN ORDER TO AVOID COMPROMISING ITS
FUNCTIONALITY.
NOTE:
ALWAYS ENSURE THE GLASS COVERS INSIDE
THE BAKING CHAMBER ARE PRESENT, OTHERWISE DUE
TO THE HEAT THAT REACHES IT, THE BULB WILL BURN
AGAIN IN A SHORT TIME.
Perform the procedure laid down in point 5.1
If the oven is cold it is possible to change it from inside the baking
chamber itself:
- Unscrew the cover (fig.16 item A) and replace the bulb (fig.16 item B):
- With the aid of a mirror insert the new light bulb and screw on the
cover.
If the oven is hot:
- Disassmble the external lateral panel of the oven from the side
corresponding to the light bulb that requires replacement (fig. 5 item. H)
- In the area near the front of the oven, remove the wool container from
the lamp area pushing downward the tab (fig. 16A part F) and then
pulling it outward.
- The lamp holder bracket will be seen (fig. 16 item.D), remove two
screws that lock it, remove the bracket and substitute the light bulb.
- Reassemble the lamp-holder bracket and correctly reposition the wool
container in its seat, THEN PUSH UPWARD THE TAB (Fig. 16A, part
F) SO THAT THE WOOL CONTAINER REMAINS CONSTRAINED
IN ITS SEAT
-Remount the external lateral panel of the oven
5.3.2 CHANGING THE PYROMETER
After carrying out the operations described in 5.1 above, to replace the
heating element proceed as follows:
- Open the sliding door and unscrew the two locking screws
- Disconnect the thermostat faston connectors;
- Replace the pyrometer (Tab. A item 20)
- Perform the above operations in reverse order to reassemble, taking
care that the connectors are inserted with the correct polarity.
5.3.3 CHANGING THE THERMOCOUPLE
After carrying out the operations described in 5.1 above, to replace the
heating element proceed as follows:
- Remove the side panel (fig. 5 item. H)
- Unfasten the nut fixing the thermocouple;
- Disconnect the two wires feeding the thermocouple;
- Replace the thermocouple (Figure 16 Item E).
- Perform the above operations in reverse order to reassemble, TAKING
CARE THAT THE CONNECTORS ARE INSERTED WITH THE
CORRECT POLARITY
5.3.4 CHANGING THE CONTACTORS
After carrying out the operations described in 5.1 above, to replace the
heating element proceed as follows:
- Remove the rear panel (fig. 8 item.A)
- Disconnect the cables on the contactor and substitute it
- Perform the above operations in reverse order to reassemble.
"SPECIAL
BULB MUST BE A HIGH