Numark NS7 Manual De Referencia página 14

TRACK CONTROLS
19. STRIP SEARCH – The length of this strip represents the length of the entire track. Place your finger on a point along this sensor
to jump to that point in the track. (If you want to scroll through a track, we recommend using your computer rather than running
your finger along the strip.)
PITCH CONTROLS
20. TAP – Tap this button at the same tempo as the track to help the software detect a more accurate BPM reading.
21. SCRATCH OFF – Press this to disable the PLATTER's motor and bring it to a stop.
22. MASTER TEMPO – If you have changed the pitch of the track, you can press the MASTER TEMPO button to return the track's
pitch to its original key. The track's tempo will remain at the speed designated by the PITCH FADER.
23. PITCH RANGE – Press this to adjust the range of the PITCH FADER to ±8%, ±16%, and ±50%.
24. PITCH FADER – Controls the track's playback speed. An LED next to the fader will light up when set at 0%.
25. PITCH BEND ( + / – ) – Press or hold down either of these buttons to temporarily adjust the track's playback speed. When
released, the track playback will return to the speed designated by the PITCH FADER.
26. BPM METER – This meter is an aid for matching the tempo of both decks. When the white center LED is lit, the BPMs are
matched. Otherwise, the meter will tend towards the faster deck. The further from center, the greater the difference between the
two BPMs.
The meter is also an aid while adjusting Loop In or Loop Out points. If you are making fine adjustments to your Loop In or Loop
Out points using the PLATTERS, the lit LED will "wrap around" the meter. It will rest on the white center LED whenever the loop's
length has been doubled or halved exactly.
Note: The BPM METER will aid in loop adjustments only if (1) a BPM reading has been entered for that track and (2) the two
Decks' tempos have been synchronized.
27. TAKEOVER LEDs – When you select the other Deck with the DECK SELECT switch, the position of the V7's PITCH FADER may
not match the Pitch setting for that Deck in the software. Slowly move the PITCH FADER in the direction indicated by the
TAKEOVER LED arrow until it turns off. At this point, the PITCH FADER matches the Pitch setting in the software and can control
it again.
NAVIGATION CONTROLS
28. SCROLL KNOB – Use this knob to scroll through lists of tracks, Crates, etc. in the software. You can also press it to move
between the panels shown in the software.
29. FWD / BACK – These buttons move the selector between various panels in the software.
30. CRATES – Press this to move the selector to the Crates Panel in the software.
31. PREPARE – Press this to move the selector to the Prepare Panel in the software.
32. FILES – Press this to move the selector to the Files Panel in the software.
33. LOAD A / LOAD B – Press one of these buttons while a track is selected to assign it to Deck A or Deck B, respectively.
Tip: Pressing the LOAD A or LOAD B button twice quickly will load the opposite Deck's track to that Deck as well, with its Audio
Pointer in the same position. For more information, see "Instant Doubles" under "Playback" in the SOFTWARE SETUP section.
34. LOAD PREPARE – Press this to add a selected track to the list of tracks in the Prepare Panel in the software.
EFFECTS CONTROLS
35. FX SELECT – Turn this knob to select an effect to apply to the channel, which will be displayed in the software. You can also
press the knob to move automatically to the next effect.
36. FX MIX – Adjusts the amount of the effect, which will be displayed the software. To hear less of the effect (a "dry" mix), move this
fader to the left. To hear more of the effect (a "wet" sound), move this fader to the right.
37. FX PARAM – Turn this knob to adjust the parameter of the effect, which will be displayed in the software.
38. FX ON / OFF – Press this button to activate or deactivate the effect. The button's LED will illuminate when the effect is on.
USB CONTROLS
39. DECK SELECT – Set this switch to assign the software Deck which the V7 will control. The left position is Deck A; the right
position is Deck B.
40. USB LED – This LED will illuminate when the V7 can communicate with a computer connected to the USB port on the rear panel.
41. LINK LED – This LED will illuminate when the V7 can communicate with another V7 connected to the LINK CONNECTION on the
rear panel.
42. MASTER BUTTON – This button determines which computer the V7 is controlling:
•
When the MASTER BUTTON is lit, the V7 is controlling the computer it is connected to via USB.
•
When the MASTER BUTTON is unlit, the V7 is controlling the computer connected to a V7 it is connected to via the LINK
CONNECTION on the rear panel.
All manuals and user guides at all-guides.com
10