Publicidad
Idiomas disponibles
Idiomas disponibles
EN
FRONT BABY SEAT FOR BICYCLE
ATTENTION
This product contains small parts like bolts, plastic bags, and small packaging hangers. Keep them out of reach of children to avoid suffocation hazards.
TABLE OF CONTENTS
TABLE OF CONTENTS OF PRODUCT
SPECIFIC INSTRUCTIONS FOR MOUNTING
How to set the bicycle seat
How to set the safety bar (only for Bilby Junior +)
How to assemble the holder in the bicycle
How to connect the bicycle seat to the holder
How to lock your holder
TABLE OF CONTENTS OF PRODUCT
A. MAIN SEAT
B. RETENTION SYSTEM HARNESS
B1. SAFETY BUCKLE
B2. HEIGHT STRAP ADJUSTERS
B3. CENTRAL STRAP ADJUSTERS
B4. SHOULDER PADDINGS
C. CUSHION
D. FOOTREST
E. FOOTREST STRAP
F. SUPPORT BAR MOUNTING KIT
F1. SUPPORT BAR MOUNTING PLATE
SPECIFIC INSTRUCTIONS FOR MOUNTING
• This child bicycle seat must not be mounted in folding bicycles.
• This child bicycle seat must not be used on speed pedelecs above 25 km/h
/ 15,5 mph.
• This child bicycle seat must not be mounted to bicycles fitted with rear
shock absorbers.
• This child bicycle seat must not be mounted to motorized vehicles such as
mopeds and scooters.
• This child bicycle seat is only suitable for carrying children with a maximum
weight of 15 Kg, and a maximum height of 93cm (and children with
recommended ages ranging from 9 months up to 3 years of age - with the
weight and height as the decisive variables).
• This child bicycle seat must not be mounted in bicycles with triangular,
square or carbon fiber frames.
• This child bicycle seat must be assembled on bicycles with round frames
with diameters ranging from Ø22 to Ø40 mm.
• The child bicycle seat must be assembled on bicycles with wheels with
diameters of 26", 27,5", 28 and 29'' .
• This child bicycle seat can be used on EPAC / Pedelecs up to 25 km/h / 15,5 mph.
HOW TO SET THE BICYCLE SEAT
1. Cut the plastic straps that hold the Holder (H).
2. Turn the child seat upside down as shown in the image. Remove the
metallic support bar (G) from the seat by cutting the straps and pulling it
upwards.
3. Use the allen key (J1) to remove the screws + washer (F2+F3) and
disengage and remove the support bar mounting plate (F1).
4. Pass both ends of the metallic support bar (G) through the openings of the
seat lower part (A). In order to adjust the child bicycle seat according to the
bicycle and child size, set the metallic support bar (G) into one of the allowed
3
HOW TO PLACE AND SECURE THE CHILD IN THE SEAT
3
HOW TO REMOVE THE SEAT FROM THE BICYCLE
3
SPECIFIC INSTRUCTIONS FOR USE
4
WARNINGS
4
MAINTENANCE
4
WARRANTY
4
F2. M8 x 16 SCREW
F3. M8 WASHER
F4. M8 NUT
F5. M8 WASHER
G. METALLIC SUPPORT BAR
H. HOLDER
H1. FRONT HOLDER PART
H2. HOLDER MOUNTING PLATE
H3. RELEASE BUTTON
H4. ADAPTER A – Ø22 a Ø30mm
H5. ADAPTER B – Ø30 a Ø40mm
• The total weight of the cyclist and the child transported must not exceed
the maximum permitted load permitted for the bicycle. Information on the
maximum load can be found in the operating instructions of the bicycle. You
can also contact the manufacturer for this question.
• The seat may only be mounted on a bicycle suitable for the attachment of
such additional loads. Please consult your bicycle instructions manual.
• The position of the child bicycle seat must be adjusted so that the bicycle
rider does not touch the child bicycle seat with the feet when in motion.
• It's very important to adjust correctly the seat and its component parts for
optimum comfort and safety of the child. It's also important that the seat
does not slope forward so that the child does not tend to slide out of it. It is
also important that the backrest slope backward slightly.
• Check if all parts of the bicycle function correctly with the child bicycle
seat mounted.
• Check the instructions of the bicycle, and If you have any doubts about
fitting the child bicycle seat to your bicycle, please contact your bicycle
supplier for further information.
positions to move the seat backward or forward. At the beginning we
suggest placing it on the position No. 1.
5. Insert the support bar mounting plate (F1) on the grooves of the seat (A), and
close it as indicated in the picture. Make sure the washer (F5) is properly placed
into the rear groove of the bicycle seat. Insert the attachment screw+washer
(F2+F3), on the back hole of the support bar mounting plate (F1). Please note
that the nut (F4) under the cushion may become loosen while tighten or loosen
the support bar mounting plate (F1). You need to grab the nut, correctly place it
on the seat groove while totally tighten the full system with the other hand. We
#polisportmove
3
H6. ATTACHMENT SCREWS M10x45
H7. HOLE FOR LOCKING-SCREW
H8. ANTI-THEFT SCREW
I. SAFETY BAR (ONLY FOR BILBY JUNIOR +)
I1+I2. SAFETY BAR CONNECTOR
J. ALLEN KEY
J1. ALLEN KEY Nº 6
J2. ALLEN KEY Nº 8
K. TRACEABILITY INFORMATION
4
4
4
5
5
6
Publicidad
