Milwaukee MXF COS350G2 Manual Original página 15

RESIDUAL RISK
Even when the product is used as prescribed, it is still impossible to
completely eliminate certain residual risk factors. The following hazards
may arise in use and the operator should pay special attention to avoid the
following:
• Injury caused by vibration
Hold the product by designated handles and restrict working time and
exposure.
• Exposure to noise can cause hearing injury.
Wear ear protection and limit exposure.
• Injury due to fl ying debris
Wear eye protection, heavy long trousers, gloves and substancial footwear
at all times.
• Inhalation of toxic dusts.
ONE-KEY™
To learn more about the ONE-KEY functionality for this tool, please reference
the Quick Start guide included with this product or go to www.milwaukeetool.
com/one-key. To download the ONE-KEY app, visit the App Store or Google
Play from your smart device.
Also, when the product experiences ESD, the Bluetooth communication will
be disconnected. It needs to be reset manually to recover.
ONE-KEY™ Indicator
Wireless mode is active and ready to be confi gured via the
Solid Blue
ONE-KEY™ app.
Blinking Blue Tool is actively communicating with the ONE-KEY™ app.
Tool is in security lockout and can be unlocked by the owner
Blinking Red
via the ONE-KEY™ app.
NOTES FOR LI-ION BATTERIES
Use of Li-Ion batteries
Batteries which have not been used for some time should be recharged
before use.
Temperatures in excess of 50°C (122°F) reduce the performance of the
battery. Avoid extended exposure to heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the batteries have to be fully charged, after used.
To obtain the longest possible battery life remove the battery pack from the
charger once it is fully charged.
For battery storage longer than 30 days:
Store the battery where the temperature is below 27°C and away from
moisture
Store the battery in a 30% - 50% charged condition
Every six months of storage, charge the battery as normal.
Battery protection for Li-Ion batteries
In extremely high torque, binding, stalling and short circuit situations that
cause high current draw, the tool will vibrate for about 5 seconds, the fuel
gauge will fl ash,and then the tool will turn OFF. To reset, release the trigger.
Under extreme circumstances, the internal temperature of the battery could
become too high. If this happens, the fuel gauge will fl ash and the battery
pack cool and then continue work.
Transport of Li-Ion batteries
Lithium-ion batteries are subject to the Dangerous Goods Legislation
requirements.
Transportation of those batteries has to be done in accordance with local,
national and international provisions and regulations.
• The user can transport the batteries by road without further requirements.
• Commercial transport of Lithium-Ion batteries by third parties is subject
to Dangerous Goods regulations. Transport preparation and transport
are exclusively to be carried out by appropriately trained persons and the
process has to be accompanied by corresponding experts.
When transporting batteries:
• Ensure that battery contact terminals are protected and insulated to
prevent short circuit.
• Ensure that battery pack is secured against movement within packaging.
• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice.
28
FUNCTIONAL DESCRIPTION
1 Guard handle
2 Guard
3 Spindle bolt
4 Wheel fl ange
5 Cutting wheel
6 LED activated machine
7 Button for activating the machine
8 Lock-off lever
9 Connection socket for cart control cable
10 Trigger
11 Quick connect fi tting
12 Water supply valve
13 Bale handle
14 Eco-coach indicator / overload indicator
15 One key™indicator
16 Hex wrench
17 Allen key
18 Roller wheels
WHEEL SELECTION
Cutting surface Cutting disc type
Non-metallic materials Silicone carbide abrasive cutting disc
Metallic materials Aluminum oxide abrasive cutting disc
Masonry materials Diamond wheel with water supply or silicone
carbide abrasive cutting disc
INDICATOR ECO COACH / OVERLOAD
Eco-Coach function
LED Cause Correction
Off Tool is not activated activate tool
On, solid Tool is activated normal operation
On, fl ashing during Nearing electronic brake immediately back off pressure
use overtemperature on wheel
On, fl ashs 10 times Overtemperature indicator, let tool cool down
then turns off tool will not start
On, fl ashing when low battery replace battery
idle
Overload control
If overloaded, the overheat protection automatically turns off the machine
and the control lamp will blink for 5 sec.
Release the trigger, after stopping remove the cut-off wheel from the
workpiece allow the machine to rest. Then switch the machine on again.
KICKBACK PROTECTION
MXF COS350G2:
This machine has a kickback protection. If the cutting disc jams, the machine
switches off .
MXF COS350RG2:
This machine is specially designed for use by rescue workers and therefore
does not have a kickback protection. This machine may only be operated by
trained personnel.
WATER CONNECTION
A water connection is available on the tool to cool the wheel and reduce
the formation of dust. The water connection should be used on all concrete
cutting applications.
For best results, allow the water to coat the entire cutting wheel before
operation.
CLEANING
The ventilation slots of the machine must be kept clear at all times.
ENGLISH
MAINTENANCE
Use only Milwaukee accessories and Milwaukee spare parts. Should
components need to be replaced which have not been described, please
contact one of our Milwaukee service agents (see our list of guarantee/
service addresses).
If needed, an exploded view of the tool can be ordered. Please state the
machine type printed as well as the six-digit No. on the label and order the
drawing at your local service agents or directly at: Techtronic Industries
GmbH, Max-Eyth-Straße 10, 71364 Winnenden, Germany.
SYMBOLS
Please read the instructions carefully before starting the machine.
CAUTION! WARNING! DANGER!
Remove the battery pack before starting any work on the machine.
Always wear goggles when using the machine.
Wear ear protectors!
Wear a suitable dust protection mask.
Wear gloves!
Do not use force.
Only for cutting work.
The guaranteed sound power level is 108 dB.
108
Do not swallow the coin cell battery!
Do not work on a ladder. Be sure to stand fi rmly.
Accessory - Not included in standard equipment, available as an
accessory.
Do not dispose of waste batteries, waste electrical and electronic
equipment as unsorted municipal waste. Waste batteries and waste
electrical and electronic equipment must be collected separately.
Waste batteries, waste accumulators and light sources have to be
removed from equipment.
Check with your local authority or retailer for recycling advice and
collection point.
According to local regulations retailers may have an obligation to take
back waste batteries and Waste electrical and electronic equipment
free of charge.
Your contribution to re-use and recycling of waste batteries and waste
electrical and electronic equipment helps to reduce the demand of
raw materials.
Waste batteries, in particular containing lithium and waste Electrical
and electronic equipment contain valuable, recyclable materials,
which can adversely impact the environment and the human health, if
not disposed of in an environmentally compatible manner.
Delete personal data from waste equipment, if any.
Rotation direction
n
Rated speed
V
Voltage
Direct Current
European Conformity Mark
UK Conformity Mark
Ukraine Conformity Mark
EurAsian Conformity Mark
ENGLISH 29