Publicidad
Idiomas disponibles
Idiomas disponibles
art_01 cassette awning installation instructions
Pull-out forces and bracket sets
Pull-out forces and bracket sets for wind resistance class 1
!
In order that the wind speed specified by us or the wind resistance class specified by us is valid, the installer must match the fastener to the substructure present. You will
receive mounting brackets for installation on concrete (C 20/25) in the case of orders received which do not contain any information about the mounting substructure. Please note
that these brackets may not be suitable for installation on other substructures. The recommended type and quantity of brackets per product must be installed to fulfil DIN EN 13561.
The specified plug pull-out forces and the installation and assembly information from the fastener manufacturers must be observed here (incl. the edge distances). Precise pull-out
forces depending on the insulating plaster thickness and the designed bracket set, as well as for installation on other substructures on request.
WALL installation on concrete C20/25
in cm
250
300
350
N
1.122
1.287
1.435
150
Set M
KI
KI
KI
1.737
1.974
2.211
N
200
KI
KI
KI
Set M
N
-
2.790
3.121
250
-
Set M
KI
KI
-
-
4.192
N
300
-
-
KI
Set M
N
-
-
-
350
-
Set M
-
-
WALL installation on brick
Mz 12
in cm
250
300
350
N
1.122
1.278
1.435
150
KI
KI
KI
Set M
1.737
883
988
N
200
Set M
KI
KM
KM
-
N
1.243
1.390
250
-
KM
KM
Set M
-
-
1.863
N
300
Set M
-
-
KM
-
N
-
-
350
-
-
-
Set M
WALL installation on hollow brick
in cm
250
300
350
504
575
143
N
150
KM
KM
KL
Set M
N
172
196
219
200
KL
Set M
KL
KL
-
276
309
N
250
-
KL
KL
Set M
N
-
-
415
300
-
Set M
-
KL
-
-
-
N
350
-
-
-
Set M
WALL installation on cellular concrete
in cm
250
300
350
1.122
575
645
N
150
Set M
KI
KM
KM
777
N
883
988
200
KM
KM
KM
Set M
-
276
309
N
250
Set M
-
KL
KL
-
N
-
415
300
-
-
KL
Set M
-
-
-
N
350
-
Set M
-
-
N = pull-out force in Newtons (N) per fixing screw;
Bracket set = provided bracket set (see overview on page 6)
X = on request
Subject to technical changes, edition 09/2023
in cm
400
450
500
1.592
1.749
1.906
KI
KI
KI
2.448
2.685
2.921
KI
KI
KI
3.452
3.782
4.113
KI
KI
KI
4.630
5.069
5.507
KI
KI
KI
5.870
6.430
7.679
KI
KI
KI
in cm
400
450
500
1.592
1.749
856
KI
KI
KM
1.094
1.200
1.305
KM
KM
KM
1.538
1.685
1.832
KM
KM
KM
458
501
454
KL
KL
KL
580
635
759
KL
KL
KL
HLz 12
in cm
400
450
500
158
174
189
KL
KL
KL
243
266
290
KL
KL
KL
342
375
407
KL
KL
KL
458
501
545
KL
KL
KL
580
X
X
KL
PB2
in cm
400
450
500
715
786
856
KM
KM
KM
290
1094
266
KM
KL
KL
342
375
407
KL
KL
KL
545
458
501
KL
KL
KL
580
635
759
KL
KL
KL
Information on recess installation
In contrast with wall or ceiling installation, no pull-out forces occur in the event
of recess installation, but rather shear forces. The maximum shear force for the
largest dimensions is approx. 87 N/mm² per screw. Please use the HW bracket
set for installation.
To install our HW bracket set, we recommend M12 steel screws (8.8) or M12
stainless steel screws (A2 70). The permissible shear stress of these screws is at
least 350 N/mm² per screw.
The installation and assembly information from the fastener manufacturers must
be observed.
7
Publicidad
