MHZ art 01 Instrucciones De Montaje página 82

art_01 cassette awning installation instructions
Adjustment instructions for Somfy Sunea io drives
NB: The awning's bottom end position is set at the factory. The top end position does not get set, as it gets moved
to via torque. No alteration is necessary unless you want to reset the bottom end position
Elektrischer Anschluss
!
green/yellow
( PE )
2
1 3
blue black empty
( N )
( L1 )
Special features of radio control systems
io radio frequency: 868,25 MHz
Features of the radio transmitters
1 W: unidirectional (one way, can transmit only)
2 W: bidirektional (two Way, können senden u. empfangen)
Installation
Product no. 99 - 4196
Changing the bottom end position
(Only necessary if the factory setting is to be altered)
The awning's bottom end position is set at the factory. The top end position
does not get set, as it gets moved to via torque. No alteration is necessary
unless you want to reset the bottom end position.
If necessary, the bottom end position can be changed. To do this, use a
control unit with no data feedback (1W), e.g. Situo Mobile io.
1. Via the 'DOWN' button, move the awning
into the bottom end position.
Drive automatically switches off.
Up / On
2. Press the 'UP' and 'DOWN' buttons simul-
taneously for c. 5 seconds until the unit
Stop
briefly moves back and forth.
Down /
Off
3. Via the 'UP' or 'DOWN' buttons set the
awning's new, desired end position.
4. Press the middle 'Stop' button until the unit
again briefly moves back and forth.
5. The bottom end position has now been
reprogrammed.
6. Trial run
26
The connecting cable must have a length of at least 30 cm left
over. If the length left over is shorter, the integrated antenna can
get damaged and there may be reception problems.
The Sunea io must be connected according to the clamp
assignments.
When making connections ensure that there is no supply of
power. (Remove the fuse!)
The system is to be protected with an upstream FI circuit breaker
in accordance with VDE regulations.
Only cables and connectors with a protection class of a minimum
of IP 54 may be used to supply power.
The control system should not be installed in the immediate vicinity of any metallic surfaces. Strong
local transmitter units (e.g. wireless headphones) that have a transmission frequency identical to the
control system can have an influence on its function.
For unidirectional transmitters (1W) the transmission range is 15 metres with no concrete walls.
For bidirectional transmitters (2W) it is up to 20 metres with two concrete walls.
The following transmitters are unidirectional (1W): Situo Mobile io, Smoove 1 io, Smoove Origin io
and Smoove A/M io.
A maximum of 9 unidirectional transmitters (1W) can be paired with each Sunea io drive. Of these
up to 3 can be wind sensors, e.g. Eolis 3D WireFree io, Eolis WireFree io. Any number of bidirectional
transmitters (2W) can be paired with the Sunea io drive.
Sunea io drives cannot be operated using an RTS radio transmitter
not be operated using an io radio transmitter
In order to be able to operate the awning during installation, the drive system must be connected to the
Somfy universal adjustment cable. For power to be supplied to the drive, the test cable's 'RTS' button
has to be pressed (supplies the Sunea io drive with continuous current). The drive can then be operated
via the hand-held radio remote control unit supplied with it.
The remote control unit has been paired with the drive. The top and bottom default end positions have
RTS
also been set at the factory and do not need any further programming. In the top end position the drive
automatically switches off when it reaches a set level of rated torque.
Note: On-site connection of drive and
control system must be done by a
specialist electrical firm.
(868,25 MHz).
Pair further control units without data feedback (1W)
(or delete paired control units without data feedback (1W))
A maximum of 9 control units without data feedback (1W) can be paired with
each Sunea io drive. Up to 3 of them can be wind sensors, e.g. Eolis 3D
WireFree io, Eolis WireFree io.
In order to pair further transmitters (or to delete them), you always need a
transmitter that has already been paired.
If no such transmitter is available to you, contact your specialist retailer to
get further information.
1. On the back of the transmitter already paired
with the radio-controlled drive press the
PROGramming button for c. 2 seconds.
The unit briefly moves and is thus 'Ready for
Pairing'
PROGramming
button
2. Briefly press the PROGramming button of the
transmitter to be newly paired (or deleted).
The unit again moves briefly back and forth.
3. The new transmitter has now been paired
(or deleted).
4. Trial run
Lay the drive's connection
cable in a downward loop so
that no water can get into the
drive.
- Damage to the internal
electronics in the drive
system.
. RTS drives can also
(433,42 MHz)
Subject to technical changes, edition 09/2023