Makita DLS110 Manual De Instrucciones página 22

Tool / battery protection system
7KH WRRO LV HTXLSSHG ZLWK D WRROEDWWHU\ SURWHFWLRQ V\V-
WHP 7KLV V\VWHP DXWRPDWLFDOO\ FXWV RII SRZHU WR WKH
PRWRU WR H[WHQG WRRO DQG EDWWHU\ OLIH 7KH WRRO ZLOO DXWR-
matically stop during operation if the tool or battery is
placed under one of the following conditions:
Overload protection
When the tool is operated in a manner that causes it to
draw an abnormally high current, the tool automatically
stops without any indication. In this situation, turn the
tool off and stop the application that caused the tool to
EHFRPH RYHUORDGHG 7KHQ WXUQ WKH WRRO RQ WR UHVWDUW
Overheat protection
On
When the tool is overheated, the tool stops automati-
cally, and the battery indicator blinks about 60 seconds.
In this situation, let the tool cool down before turning the
tool on again.
Overdischarge protection
When the battery capacity becomes low, the tool stops
automatically. If the product does not operate even
when the switches are operated, remove the batteries
from the tool and charge the batteries.
Indicating the remaining battery
capacity
Fig.9: 1. Battery indicator 2. Check button
Press the check button to indicate the remaining battery
FDSDFLWLHV 7KH EDWWHU\ LQGLFDWRUV FRUUHVSRQG WR HDFK
battery.
Battery indicator status
On Off
Blinking
Remaining
battery
capacity
Blinking
50% to 100%
20% to 50%
0% to 20%
Charge the
battery
22 ENGLISH
Indicating the remaining battery
capacity
Only for battery cartridges with the indicator
Fig.10: 1. Indicator lamps 2. Check button
Press the check button on the battery cartridge to indi-
FDWH WKH UHPDLQLQJ EDWWHU\ FDSDFLW\ 7KH LQGLFDWRU ODPSV
light up for a few seconds.
Indicator lamps
Lighted Off
NOTE: Depending on the conditions of use and the
ambient temperature, the indication may differ slightly
from the actual capacity.
Automatic speed change function
Fig.11: 1. Mode indicator
Mode indicator status
On
7KLV WRRO KDV KLJK VSHHG PRGH DQG KLJK WRUTXH
PRGH  ,W DXWRPDWLFDOO\ FKDQJHV RSHUDWLRQ PRGH
depending on the work load. When mode indicator
OLJKWV XS GXULQJ RSHUDWLRQ WKH WRRO LV LQ KLJK WRUTXH
mode.
Blade guard
Fig.12: 1. Blade guard
When lowering the handle, the blade guard rises auto-
PDWLFDOO\ 7KH JXDUG LV VSULQJ ORDGHG VR LW UHWXUQV WR
its original position when the cut is completed and the
handle is raised.
WARNING:
Never defeat or remove the blade
guard or the spring which attaches to the guard.
$Q H[SRVHG EODGH DV D UHVXOW RI GHIHDWHG JXDUGLQJ
PD\ UHVXOW LQ VHULRXV SHUVRQDO LQMXU\ GXULQJ RSHUDWLRQ
Remaining
capacity
Blinking
75% to 100%
50% to 75%
25% to 50%
0% to 25%
Charge the
battery.
7KH EDWWHU\
may have
malfunctioned.
Operation mode
Off
High speed mode
+LJK WRUTXH PRGH