Carrying Tool - Makita DLS110 Manual De Instrucciones

Crown molding stopper
Optional accessory
Crown molding stoppers allow easier cuts of crown
molding without tilting the saw blade. Install them on the
WXUQ EDVH DV VKRZQ LQ WKH ¿JXUHV
At right 45° miter angle
Fig.52: 1. Crown molding stopper L 2. Crown mold-
ing stopper R 3. 7XUQ EDVH 4. Guide fence
At left 45° miter angle
Fig.53: 1. Crown molding stopper L 2. Crown mold-
ing stopper R 3. 7XUQ EDVH 4. Guide fence
3RVLWLRQ FURZQ PROGLQJ ZLWK LWV :$// &217$&7 ('*(
DJDLQVW WKH JXLGH IHQFH DQG LWV &(,/,1* &217$&7 ('*(
DJDLQVW WKH FURZQ PROGLQJ VWRSSHUV DV VKRZQ LQ WKH ¿JXUH
$GMXVW WKH FURZQ PROGLQJ VWRSSHUV DFFRUGLQJ WR WKH VL]H RI
WKH FURZQ PROGLQJ 7LJKWHQ WKH VFUHZV WR VHFXUH WKH FURZQ
molding stoppers. Refer to the table (C) for the miter angle.
Fig.54: 1. Guide fence 2. Crown molding stopper
(a) (b)
1
1. Inside corner 2. Outside corner
Table (C)
– Molding
position in
WKH ¿JXUH
For inside (a)
corner
(b)
For outside (c)
corner
(d)
Cutting aluminum extrusion
Fig.55: 1. Vise 2. Spacer block 3. Guide fence
4. $OXPLQXP H[WUXVLRQ 5. Spacer block
When securing aluminum extrusions, use spacer blocks or pieces
RI VFUDS DV VKRZQ LQ WKH ¿JXUH WR SUHYHQW GHIRUPDWLRQ RI WKH DOX-
minum. Use a cutting lubricant when cutting the aluminum extru-
sion to prevent build-up of the aluminum material on the blade.
WARNING:
Never attempt to cut thick or
round aluminum extrusions. 7KLFN RU URXQG DOXPL-
QXP H[WUXVLRQV FDQ EH GLI¿FXOW WR VHFXUH DQG WKH ZRUN
may loosen during the cutting operation which may
UHVXOW LQ ORVV RI FRQWURO DQG VHULRXV SHUVRQDO LQMXU\
(c) (d)
2
Miter angle Finished
piece
Right 45° Save the right
side of blade
Left 45° Save the left
side of blade
Save the right
side of blade
Right 45° Save the left
side of blade
Groove cutting
WARNING:
type of cut by using a wider type blade or dado
blade. $WWHPSWLQJ WR PDNH D JURRYH FXW ZLWK D ZLGHU
blade or dado blade could lead to unexpected cutting
results and kickback which may result in serious
SHUVRQDO LQMXU\
WARNING:
to the original position when performing other
than groove cutting. $WWHPSWLQJ WR PDNH FXWV ZLWK
the stopper arm in the incorrect position could lead to
unexpected cutting results and kickback which may
UHVXOW LQ VHULRXV SHUVRQDO LQMXU\
For a dado type cut, perform as follows:
1. $GMXVW WKH ORZHU OLPLW SRVLWLRQ RI WKH EODGH XVLQJ
WKH DGMXVWLQJ VFUHZ DQG WKH VWRSSHU DUP WR OLPLW WKH FXW-
WLQJ GHSWK RI WKH EODGH 5HIHU WR 6WRSSHU DUP VHFWLRQ
described on previously.
2. $IWHU DGMXVWLQJ WKH ORZHU OLPLW SRVLWLRQ RI WKH EODGH
cut parallel grooves across the width of the workpiece
using a slide (push) cut.
Fig.56: 1. Cut grooves with blade
3. Remove the workpiece material between the
grooves with a chisel.

Carrying tool

Before carrying, make sure to remove the batteries and
DOO PRYDEOH SDUWV RI WKH PLWHU VDZ DUH VHFXUHG $OZD\V
check the following:
‡ 7KH EDWWHULHV DUH UHPRYHG
‡ 7KH FDUULDJH LV DW ƒ EHYHO DQJOH SRVLWLRQ DQG
secured.
‡ 7KH FDUULDJH LV ORZHUHG DQG ORFNHG
‡ 7KH FDUULDJH LV IXOO\ VOLG WR WKH JXLGH IHQFH DQG
locked.
‡ 7KH WXUQ EDVH LV DW WKH IXOO ULJKW PLWHU DQJOH SRVL-
tion and secured.
‡ 7KH KROGHUV DUH VWRUHG DQG VHFXUHG
Carry the tool by holding both sides of the tool base as
VKRZQ LQ WKH ¿JXUH
Fig.57
WARNING:
is for carrying and storage purposes only and not
for any cutting operations. 7KH XVH RI WKH VWRSSHU
pin for cutting operations may cause unexpected
movement of the saw blade resulting in kickback and
VHULRXV SHUVRQDO LQMXU\
CAUTION:
Always secure all moving portions
before carrying the tool. If portions of the tool move
or slide while being carried, loss of control or balance
PD\ RFFXU DQG UHVXOW LQ SHUVRQDO LQMXU\
30 ENGLISH
Do not attempt to perform this
Be sure to return the stopper arm
Stopper pin for carriage elevation