Makita DLS110 Manual De Instrucciones página 31

WIRELESS ACTIVATION
FUNCTION
For DLS111 only
What you can do with the wireless
activation function
7KH ZLUHOHVV DFWLYDWLRQ IXQFWLRQ HQDEOHV FOHDQ DQG FRP-
fortable operation. By connecting a supported vacuum
cleaner to the tool, you can run the vacuum cleaner
automatically along with the switch operation of the tool.
Fig.58
7R XVH WKH ZLUHOHVV DFWLYDWLRQ IXQFWLRQ SUHSDUH IROORZ-
ing items:
‡ $ ZLUHOHVV XQLW
‡ $ YDFXXP FOHDQHU ZKLFK VXSSRUWV WKH ZLUHOHVV
activation function
7KH RYHUYLHZ RI WKH ZLUHOHVV DFWLYDWLRQ IXQFWLRQ VHWWLQJ
is as follows. Refer to each section for detail procedures.
1. Installing the wireless unit
2. 7RRO UHJLVWUDWLRQ IRU WKH YDFXXP FOHDQHU
3. Starting the wireless activation function
Installing the wireless unit
CAUTION:
3ODFH WKH WRRO RQ D ÀDW DQG VWDEOH
surface when installing the wireless unit.
NOTICE:
Clean the dust and dirt on the tool before
installing the wireless unit. Dust or dirt may cause
malfunction if it comes into the slot of the wireless unit.
NOTICE:
To prevent the malfunction caused by
static, touch a static discharging material, such
as a metal part of the tool, before picking up the
wireless unit.
NOTICE:
When installing the wireless unit, always
be sure that the wireless unit is inserted in the cor-
rect direction and the lid is completely closed.
1. 2SHQ WKH OLG RQ WKH WRRO DV VKRZQ LQ WKH ¿JXUH
Fig.59: 1. Lid
2. Insert the wireless unit to the slot and then close
the lid.
:KHQ LQVHUWLQJ WKH ZLUHOHVV XQLW DOLJQ WKH SURMHFWLRQV
with the recessed portions on the slot.
Fig.60: 1. Wireless unit 2. 3URMHFWLRQ 3. Lid
4. Recessed portion
When removing the wireless unit, open the lid slowly.
7KH KRRNV RQ WKH EDFN RI WKH OLG ZLOO OLIW WKH ZLUHOHVV XQLW
as you pull up the lid.
Fig.61: 1. Wireless unit 2. Hook 3. Lid
$IWHU UHPRYLQJ WKH ZLUHOHVV XQLW NHHS LW LQ WKH VXSSOLHG
case or a static-free container.
NOTICE:
Always use the hooks on the back of
the lid when removing the wireless unit. If the
hooks do not catch the wireless unit, close the lid
completely and open it slowly again.
Tool registration for the vacuum
cleaner
NOTE: $ 0DNLWD YDFXXP FOHDQHU VXSSRUWLQJ WKH
ZLUHOHVV DFWLYDWLRQ IXQFWLRQ LV UHTXLUHG IRU WKH WRRO
registration.
NOTE: Finish installing the wireless unit to the tool
before starting the tool registration.
NOTE: During the tool registration, do not pull the
switch trigger or turn on the power switch on the
vacuum cleaner.
NOTE: Refer to the instruction manual of the vacuum
cleaner, too.
If you wish to activate the vacuum cleaner along with
WKH VZLWFK RSHUDWLRQ RI WKH WRRO ¿QLVK WKH WRRO UHJLVWUD-
tion beforehand.
1. Install the batteries to the vacuum cleaner and the
tool.
2. Set the stand-by switch on the vacuum cleaner to
$872 
Fig.62: 1. Stand-by switch
3. Press the wireless activation button on the vac-
uum cleaner for 3 seconds until the wireless activation
ODPS EOLQNV LQ JUHHQ $QG WKHQ SUHVV WKH ZLUHOHVV DFWL-
vation button on the tool in the same way.
Fig.63: 1. Wireless activation button 2. Wireless
activation lamp
If the vacuum cleaner and the tool are linked success-
fully, the wireless activation lamps will light up in green
for 2 seconds and start blinking in blue.
NOTE: 7KH ZLUHOHVV DFWLYDWLRQ ODPSV ¿QLVK EOLQNLQJ
in green after 20 seconds elapsed. Press the wireless
activation button on the tool while the wireless acti-
vation lamp on the cleaner is blinking. If the wireless
activation lamp does not blink in green, push the wire-
OHVV DFWLYDWLRQ EXWWRQ EULHÀ\ DQG KROG LW GRZQ DJDLQ
NOTE: When performing two or more tool registra-
WLRQV IRU RQH YDFXXP FOHDQHU ¿QLVK WKH WRRO UHJLVWUD-
tion one by one.
Starting the wireless activation
function
NOTE: Finish the tool registration for the vacuum
cleaner prior to the wireless activation.
NOTE: Refer to the instruction manual of the vacuum
cleaner, too.
$IWHU UHJLVWHULQJ D WRRO WR WKH YDFXXP FOHDQHU WKH
vacuum cleaner will automatically runs along with the
switch operation of the tool.
1. Install the wireless unit to the tool.
2. Connect the hose of the vacuum cleaner with the
tool.
Fig.64
3. Set the stand-by switch on the vacuum cleaner to
$872 
Fig.65: 1. Stand-by switch
31 ENGLISH