JVC TH-M65 Manual De Instrucciones página 21

Getting started
4
Press number buttons (1-9, 0) to enter
the manufacturer's code (2 digits).
Examples:
For a GI Jerrold product: Press 0, then 1.
For a Sony product: Press 2, then 0.
Manufacturer
Echostar
GI Jerrold
Hamin/Regal
Pioneer
RCA
Scientific Atlanta
Sony
Zenith
5
Release DBS.
6
Try operating your DBS tuner or CATV
converter by pressing . VCR/DBS.
When your DBS tuner or CATV converter turns on or off, you
have entered the correct code.
If there is more than one code listed for your brand, try each
one until you enter the correct one.
NOTE
• Manufacturers' codes are subject to change without notice. If they are
changed, this remote control cannot operate the equipment.
• Set the codes again after replacing the batteries of the remote control.
% Operation
IMPORTANT
Before using the remote control to operate a
DBS tuner or CATV converter;
1 Set the remote control mode selector to
VCR/DBS.
2 Press DBS.
The following buttons are available:
F VCR/DBS:
Turns DBS tuner or CATV converter on and
off.
CHANNEL +/–:* Changes the channels.
1-10, 0, +10 (100+): Selects the channel.
* Be sure to set the Karaoke mode switch to OFF before using
CHANNEL +/–. (for TH-M65 only)
For VCR operations
You can operate your VCR using the remote control supplied with
this system.
• Refer also to the instruction manuals supplied with your VCR.
% To set the manufacturer's code
1
Slide the remote control mode selector
to VCR/DBS.
2
Press and hold VCR.
Keep the button pressed until step 4 is finished.
3
Press ENTER.
Code
21
01, 02, 03, 04, 05, 06, 07, 08
15, 16, 17, 18
13, 14
19
09, 10
20
11, 12
4
Press number buttons (1-9, 0) to enter
the manufacturer's code (2 digits).
Examples:
For a Philips VCR: Press 0, then 9.
For an NEC VCR: Press 2, then 5.
Manufacturer Code
JVC 01, 02, 03
Emerson 11, 26
Fisher 29
Funai 10, 14, 15, 16
Gold Star 12
Hitachi 04
Mitsubishi 13
NEC 25
Panasonic 07, 17
5
Release VCR.
6
Try operating your VCR by pressing
. VCR/DBS.
When your VCR turns on or off, you have entered the correct
code.
If there is more than one code listed for your brand, try each
one until you enter the correct one.
NOTE
• Manufacturers' codes are subject to change without notice. If they are
changed, this remote control cannot operate the equipment.
• Set the codes again after replacing the batteries of the remote control.
% Operation
IMPORTANT
Before using the remote control to operate a
VCR;
1 Set the remote control mode selector to
VCR/DBS.
2 Press VCR.
The following buttons are available:
F VCR/DBS:
Turns VCR on and off.
3 (play button): Starts playback.
7 :
Stops operation.
8 :
Pauses playback.
¢ :
Fast forwards video tape.
4 :
Rewinds video tape.
Press this button together with 3 (play button)
REC:
to start recording or together with 8 to pause
recording.
CHANNEL +/–*: Changes the TV channels on the VCR.
1-10, 0: Selects the channel. (for the JVC's VCR only)
* Be sure to set the Karaoke mode switch to OFF before using
CHANNEL +/–. (for TH-M65 only)
NOTE
When operating a VCR or DBS tuner/CATV converter;
• The source setting of VCR or DBS remains after you have changed
the remote control mode selector to AUDIO or TV. When operating
VCR or DBS tuner/CATV converter again, it is not necessary to press
VCR or DBS after setting the remote control mode selector.
Manufacturer Code
Philips 09
RCA 05, 06
Samsung 24
Sanyo 21, 22, 23
Sharp 27, 28
Shintom 30
Sony 18, 19, 20
Zenith 08
18