Storage And Transport - DBI SALA ULTRA-LOK 3504553 Manual Del Usuario

6.0 MAINTENANCE, SERVICING, AND STORAGE
6.1 CLEANING: Cleaning procedures for the Self-Retracting Lanyard are as follows:
• Periodically clean the exterior of the SRL using water and a mild soap solution. Position the SRL so
excess water can drain out. Clean labels as required.
• Clean lifeline with water and mild soap solution. Rinse and thoroughly air dry. Do not force dry with
heat. An excessive buildup of dirt, paint, etc. may prevent the lifeline from fully retracting back into the
housing causing a potential free fall hazard. Replace lifeline if excessive buildup is present.
6.2 SERVICE: Additional maintenance and servicing procedures must be completed by an authorized service
center. Do not attempt to disassemble the SRL or lubricate any parts.
6.3 STORAGE AND TRANSPORT: Store and transport Self-Retracting Lanyard in a cool, dry, clean environment
out of direct sunlight. Avoid areas where chemical vapors may exist. Thoroughly inspect the SRL after any
period of extended storage.
7.0 LABELS
Figure 19 illustrates labels on the the Ultra-Lok SRLs and their locations. All label must be present on the SRL.
Labels must be replaced if they are not fully legible. Information provided on each label is as follows:
1) Inspect locking action of SRL. Should hear an audible noise when SRL locks. 2) Read instructions.
A
This product is i-Safe enabled and contains an electronic tag that can be read by compatible readers) providing inspection
B
logs, inventory management, and other safety information.
EN341 Descent Specifi cations: 1) One person maximum. 2) Always anchor SRL overhead. 3) RSQ Descent Speed Range
C
= 6-9 m/s.
Do not load SRL over and edge.
D
1) Dexcent Mode selection 2) Fall Arrest Mode selection
E
Pull RSQ Engagement Knob out and turn until arrow points to selected mode.
F
1) Never anchor SRL level with or below the back dorsal harness connection point. 2) Read instructions. 3) Inspect Snap
G
Hook Impact Indicator. Do not use if impact is indicated.
Fall Arrest
H
1) Manufactured (Year/Monty) 2) Lot Number 3) Model Number 4) Material 5) Length 6) Serial Number
I
EN360 SRL Fall Arrest Specifi cations: 1) Maximum Capacity is one person not exceeding 141 kg with a Maximum
J
Arresting Force of 6 kN. 2) Minimum Clearance when anchored directly overhead is 2 m. 3) Average Locking Speed is
1.4 m/s.
Rotate Retrieval Handle clockwise to raise. Rotate Retrieval Handle counterclockwise to lower.
K
Retrieval Operation: 1) Loosen Locking Thumbscrew. 2) Rotate the Retrieval Handle up. 3) Pull and hold the Shift Knob.
L
4) Push the Crank in and release the Shift Knob. If needed, rotate the Crank Arm clockwise slightly to engage the gear.
Rotate Crank Arm clockwise to lift. Rotate Crank Arm counterclockwise to lower. E) Release Shift Knob to lock Crank Arm.
1) Never anchor SRL level with or below the back dorsal harness connection point. 2) Read instructions. 3) Inspect
M
Snaphook and Lifeline. 4) Inspect locking action of SRL. Should hear an audible noise when SRL locks. 5) All labels
should be present and legible. 6) Control Lifeline while it retracts into the SRL. 7) Inspect Snap Hook Impact Indicator.
Do not use if impact is indicated.
1) Read instructions. 2) nspect Snaphook and Lifeline. 3) Inspect locking action of SRL. Should hear an audible noise
N
when SRL locks. 4) Control Lifeline while it retracts into the SRL. 5) All labels should be present and legible. 6) Do not
repair. 7) Service and repair should only be performed by Capital Safety authorized personnel.
1) Manufactured (Year/Monty) 2) Lot Number 3) Model Number 4) Material 5) Length 6) Serial Number 7) See
O
specifi cation section of label for Lifeline material designation. 8) Do not remove this label.
EN360 SRL Fall Arrest Specifi cations: 1) Maximum Capacity is one person not exceeding 141 kg with a Maximum
P
Arresting Force of 6 kN. 2) Minimum Clearance when anchored directly overhead is 2 m.
14