Adjustment System For Mig/Mag Welding Process; Adjustment System For Mig/Mag Standard Welding Process Manual Program; Adjustment System For Mig/Mag Standard Welding Process Synergic Process - GALAGAR INVERMIG SYNER 230 MP Bi-PULSE Manual Técnico De Instrucciones

3.4.3. ADJUSTMENT SYSTEM FOR MIG/MAG WELDING PROCESS.

3.4.3.1. ADJUSTMENT SYSTEM FOR STANDARD MIG/MAG WELDING PROCESS. MANUAL PROGRAM.
P1: SELECT PROCESS
3.4.3.2. ADJUSTMENT SYSTEM FOR STANDARD MIG/MAG WELDING PROCESS. SYNERGIC PROCESS.
Material display
Fe Ar
SS Ar
CuSi Ar
Standard
Fe
Al Si Ar
Al Mg Ar
Fe
Fe Ar
P1: SELECT PROCESS
GALA INVERMIG SYNER 230 MP Bi-PULSE
P2: SELECT
WELDING
PROGRAM
MANUAL
8 FIELDS display
Gas display
D1
P00
P01
CO 18%
2
P02
P03
P04
CO 2% P05
2
P06
P07
P08
P09
FCAW P10
P11
P12
P13
P14
P15
P16
CO
P17
2
P18
CO 18% P19
2
Prog. nº.
P2: SELECT
WELDING
PROGRAM
Ss
Ar CO 2%
2
E1: ADJUST WELDING
VOLTAGE
Display D2:
Wire display
D2 D3 mm in
SG2 SG3 0,6 0,023
SG2 SG3 0,8 0,030
SG2 SG3 --- 0,035
SG2 SG3 1,0 ---
308 LSi 0,8 0,030
308 LSi --- 0,035
308 LSi 1,0 ---
Cu Si3 % --- 0,035
Cu Si3 % 1,0 ---
E71 T11 0,8 0,030
E71 T11 --- 0,035
E71 T11 1,0 ---
AL Si5 % 1,2 0,045
AL MG5 % 1,0 ---
AL MG5 % --- 0,045
AL MG5 % 1,2 ---
SG2 SG3 0,8 0,030
SG2 SG3 --- 0,035
SG2 SG3 1,0 ---
NO Cu 1,0 ---
Wire type
P3: SELECT WIRE E2: SELECT WELDING
DIAMETER PIECE THICKNESS
1.0 mm
E2: ADJUST WIRE SPEED
V
e(mm)
min. max.
0,5 4,0 SG 2/ SG 3 Si 1:
0,8 6,0 Non-alloy or low alloy wire.
0,7 6,0 (Solid Fe)
0,9 5,0 Gas mixture Ar-CO
0,9 3,2 Cr Ni 19-9
0,9 6,0 Solid stainless steel wire (Stainless)
0,8 7,0 ER 308 ; E308L-16
0,8 4,5 CuSi3
0,8 4,5 Cu-Si wire for electrocoating welding.
1,0 5,0 FCAW 71T11
1,0 5,0 Tubular wire filled with rutile flux (TYPE 71T11)
1,5 5,0
1,6 6,0 Al Si 5% Aluminum wire alloyed with Silicon.
1,0 6,3 Al Mg 5%
1,2 6,0
1,8 6,0 Aluminum wire alloyed with Magnesium.
0,8 4,5 SG2 / SG3 Si 1. (Solid Fe) Gas CO
1,0 5,5 Non-alloy or low alloy wire.
1,2 6,0 Penetration and wire speed increase.
0,9 5,0 Greater stability and less projections.
mm
50
Display D1:
m/ min
Remarks
12 ÷ 25%
2
100%
2
E1: CORRECTING
WELDING VOLTAGE
(ARC HEIGHT)
-30 % TO + 30%
%