Putting Into Operation - Brill 380 ASM Manual Del Usuario

cutting height you require
(fig. O) :
Highest cutting height:
GB
Lowest cutting height:

6. Putting into operation

6.1.Charging the PowerAccu
( fig. P)
For technical reasons the Power-
Accu (20) is not charged. Con-
sequently, the unit needs to be
charged before initial operation.
For this exclusively use the
Charger LG 24 (21).
Plug the charger (21) into the
mains socket and then push the
plug for the charger (22) into
the charging socket (23) of
the PowerAccu. The charging
procedure begins.
Ensure you use the correct
mains voltage!
Charging time: approx. 24 hours
for the initial charge. Afterwards,
12 - 24 hours depending on the
state of charge.
The PowerAccu reaches its full
capacity only after numerous
(approx. 5) charging/discharg-
ing processes.
Do not charge the Power-
A
Accu with charging equip-
ment other than the Charger
LG 24 since only this charger
has been specifically adapted
for use with the PowerAccu.
The use of other charging units
can lead to damage and injuries.
The use of other charging units
makes all claims for compen-
22
Note : Make sure that the
arrows marking the cutting
height (8) show the same
45 mm
cutting height on both sides
of the scale (fig. O1).
20 mm
5. Re-tighten both fixing nuts (9)
(fig. N).
sation null and void and releases
the manufacturer from all gua-
rantee services.
Charge the PowerAccu
A
for 24 hours before using
your Accu Hand Lawnmower
for the first time.
The mains plug (21) heats
A
up slightly during the
charging procedure.
Charge the PowerAccu
A
in a dry place and away
from direct sunlight.
Never charge the Power-
A
Accu anywhere near
easily inflammable materials.
6.2. Connecting the PowerAccu
(fig Q – T)
1. Open the harness compart-
ment (fig. Q). Hold the Power-
Accu in your right hand and
use your left hand to pull
the harness to the left so that
the ends of the harness lie
flat against the PowerAccu
(fig. R).
2. Push the PowerAccu into the
contact bar (24) until you
hear it click into place (fig. S).
3. Fold the harness into loops,
stow it away in the harness
compartment (fig. T) and
close the cover (13). This
also secures the PowerAccu
in the contact bar.
Note : When setting the Accu
Hand Lawnmower to a low
cutting height, ensure that
the lower blade and cutting
cylinder do not touch the
ground if the ground is un-
even.
6.3. Starting your mower (fig. U)
Warning ! Before starting your
Accu Hand Lawnmower check
for foreign bodies in the cutting
cylinder and remove if neces-
sary.
Start your Accu Hand Lawn-
mower as follows:
1. Stand your mower on a level
part of the lawn.
2. To start the motor, press and
hold down the release knob
(15) (fig. U) and with the
other hand, simultaneously
pull the starting handle (16)
towards the cross bar
(fig. U).
3. If you release the starting
handle (16) the motor switch-
es off again.
The switches installed
A
by the manufacturer must
not be removed or be bridged
eg : by taping down the starting
handle (16) to the guide handle.
This will prevent the mower swit-
ching off automatically,
and could cause fatal injury.
Attention ! Cutting cylinder con-
tinue to run for a few seconds
after the motor is switched off.
When working with the Accu
Hand Lawnmower the Accu heats
up ; this is normal and does not
affect its performance.