CST/BERGER RL25H Manual Original página 37

Marking
When the laser beam runs through the centre of the reception
area 35, its height can be marked at the centre mark 40 right
and left on the measuring tool. The centre mark is located
50.8 mm away from the top edge of the measuring tool.
When marking, take care to align the measuring tool exactly
vertical (for horizontal laser beam), or horizontal (for vertical
laser beam), as otherwise the marks are offset with respect to
the laser beam.
Attaching with the Holder (see figure C)
With the holder 48, the measuring tool can be fastened to a "Cut
& fill" rod 50 (accessory) as well as to other auxiliary tools with
a width of up to 65 mm.
Screw the holder 48 to the retainer opening 47 on the rear side
of the measuring tool with fastening screw 51.
Loosen locking screw 49, slide the holder, e.g., onto the "Cut &
fill" rod 50 and tighten locking screw 49 again.
The holder 48 can be horizontally aligned with help of the spirit
level 52.
A measuring tool mounted out-of-level leads to faulty measure-
ments.
Maintenance and Service
Maintenance and Cleaning
Keep the measuring tool clean at all times.
When heavily contaminated, the measuring tool can be cleaned
under running water. Do not immerse the measuring tool in wa-
ter and do not subject it to a high-pressure water jet.
Wipe off debris using a moist and soft cloth. Do not use any
cleaning agents or solvents.
If the measuring tool should fail despite the care taken in manu-
facturing and testing procedures, repair should be carried out
by an authorised after-sales service centre for Bosch power
tools. Do not open the measuring tool yourself.
In all correspondence and spare parts orders, please always in-
clude the 10-digit article number given on the type plate of the
measuring tool.
After-sales Service and Customer Assistance
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
Tel. Service: +44 (0844) 736 0109
Fax: +44 (0844) 736 0146
E-Mail: boschservicecentre@bosch.com
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: +353 (01) 4 66 67 00
Fax: +353 (01) 4 66 68 88
2 610 A15 294 • 7.5.12
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: +61 (01300) 307 044
Fax: +61 (01300) 307 045
Inside New Zealand:
Phone: +64 (0800) 543 353
Fax: +64 (0800) 428 570
Outside AU and NZ:
Phone: +61 (03) 9541 5555
www.bosch.com.au
Republic of South Africa
Customer service
Hotline: +27 (011) 6 51 96 00
Gauteng – BSC Service Centre
35 Roper Street, New Centre
Johannesburg
Tel.: +27 (011) 4 93 93 75
Fax: +27 (011) 4 93 01 26
E-Mail: bsctools@icon.co.za
KZN – BSC Service Centre
Unit E, Almar Centre
143 Crompton Street
Pinetown
Tel.: +27 (031) 7 01 21 20
Fax: +27 (031) 7 01 24 46
E-Mail: bsc.dur@za.bosch.com
Western Cape – BSC Service Centre
Democracy Way, Prosperity Park
Milnerton
Tel.: +27 (021) 5 51 25 77
Fax: +27 (021) 5 51 32 23
E-Mail: bsc@zsd.co.za
Bosch Headquarters
Midrand, Gauteng
Tel.: +27 (011) 6 51 96 00
Fax: +27 (011) 6 51 98 80
E-Mail: rbsa-hq.pts@za.bosch.com
People's Republic of China
China Mainland
Bosch Power Tools (China) Co., Ltd.
567, Bin Kang Road
Bin Jiang District 310052
Hangzhou, P.R.China
Service Hotline: 400 826 8484
Fax: +86 571 8777 4502
E-Mail: contact.ptcn@cn.bosch.com
www.bosch-pt.com.cn
English | 37