Stryker Power-PRO IT Manual De Uso página 36

Camilla
Ocultar thumbs Ver también para Power-PRO IT:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

2. Release the head section release handle, then push the head section toward the litter frame. Retract the head section to
the retracted position.
3. Release the head section release handle to lock the head section in the retracted position.
A A p p p p l l y y i i n n g g o o r r r r e e l l e e a a s s i i n n g g a a w w h h e e e e l l l l o o c c k k
W W A A R R N N I I N N G G
• Do not apply a wheel lock when a patient is on the product or when you move the product to avoid the risk of tipping.
• Do not install or apply a wheel lock on a product with worn wheels that are less than 6 in. diameter.
• Do not leave a patient or occupant unattended. Hold the product while a patient or occupant is on the product.
To apply a wheel lock, press down on the pedal until it stops and is resting against the surface of the wheel.
To release a wheel lock, press down on the top of the pedal with your foot or lift up on the pedal with your toe. The top of the
pedal will rest against the caster frame when you release the wheel lock.
N N o o t t e e - - Wheel locks help prevent the product from rolling while unattended. Wheel locks may not provide sufficient
resistance on all surfaces or under loads.
A A p p p p l l y y i i n n g g o o r r r r e e l l e e a a s s i i n n g g t t h h e e o o p p t t i i o o n n a a l l S S t t e e e e r r - - L L O O C C K K
To apply the Steer-LOCK:
1. From the cot foot end, press the red (lock) side of the foot pedal or from the cot head end, press down on either red
pedal.
2. Rotate the cot until at least one head end caster locks.
To release the Steer-LOCK:
From the cot foot end, press the green (unlock) side of the foot pedal or from the cot head end, lift up on either red pedal
at the head end.
I I n n s s t t a a l l l l i i n n g g t t h h e e i i n n c c u u b b a a t t o o r r a a d d a a p p t t o o r r
W W A A R R N N I I N N G G
• Do not install these incubator adaptors on any other Stryker cot or on any cot from another manufacturer. These
incubator adaptors are for use only on the P P o o w w e e r r - - P P R R O O IT cot.
• Always make sure that the incubator adaptor is properly installed on the cot and the incubator is securely fastened to the
incubator adaptor before use.
N N o o t t e e
• If the incubator adaptor was ordered with the P P o o w w e e r r - - P P R R O O IT cot, the incubator adaptor may have been installed at the
factory.
• If the incubator adaptor was purchased as a retrofit kit, follow these instructions for installation.
To install the incubator adaptor:
1. Remove the existing incubator adaptor if there is one already present.
2. Install the new incubator adaptor.
3. Align the incubator adaptor assembly with the mounting holes in the P P o o w w e e r r - - P P R R O O IT cot.
4. Install the provided fasteners. Apply a few drops of the provided Loctite® to the threads of the fasteners and tighten.
EN
32
6516-209-005 Rev E.0

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

6516

Tabla de contenido