Kenwood KAX92.AOME Manual De Instrucciones página 4

A B C
Fit the securing nut and
hand tighten. (Do not use
the spanner/pusher as this is
K L M
to assist with removal only).
Make sure the securing nut
l
is almost flush against the
U V W
body of the attachment.
A B
B C D
Lift off the slow speed outlet
cover.
C D E
With the attachment in
1
K L
L M N
position shown, locate to the
2
slow speed outlet and rotate
M N O
U V to lock in place.
3
V W X
D E F
Fit the hopper.
4
W X Y
5
Cutting Assembly
N O P
6
Optional: The cutting assembly
and
7
X Y Z
assembled pasta shaper to assist
8
with cutting the pasta into the
desired lengths.
9
A B C
10
E F G
With the handle of the
cutting blade uppermost,
11
unscrew the clamp ring
K L M
12
O P Q
slightly. Place over the
securing nut and twist if
13
necessary until fully home
U V W
Y Z
14
on the attachment. The die
should fit flush with the front
15
of the cutting assembly.
16
Hold the edge of the cutting
assembly and at the same
17
time tighten the clamp ring
18
by turning away from you.
Note: Whenever you fit
19
or remove the cutting
20
assembly, always hold the
edge of the assembly in one
21
hand and twist the clamp
22
ring with the other.
23
To Use Your Pasta
24
shaper
25
C C D D E E
Refer to illustrations
26
Use speeds 2-3 to process
l
27
your pasta.
M M N N O O
Make your pasta mix
l 28
following a recipe supplied.
29
Do not make the mix too
l
W W X X Y Y
dry as it could break your
30
pasta shaper or machine.
31
32
33
34
5720001833 Iss 2 KAX92.A0ME multi.indd 4 5720001833 Iss 2 KAX92.A0ME multi.indd 4
D E F
N O P
X Y Z
C D E
E F G
1 51
F G H
2 51 52
M N O
O P Q
3 52 53
P Q R
W X Y
4 53 54
Y Z
G H I
5 54 55
Z
6 55 56
Q R S
7 56 57
can be fitted to the
8 57 58
9 58 59
10 59 60
D E F
11 60 61
H I J
12 61 62
N O P
13 62 63
R S T
14 63 64
X Y Z
15 64 65
16 65 66
17 66 67
18 67 68
19 68 69
20 69 70
21 70 71
22 71 72
23 72 73
24 73 74
25 74 75
75
26 76
F F G G H H
27 76 77
28 77 78
P P Q Q R R
29 78 79
79
30 80
Z Z
31 80 81
32 81 82
33 82 83
83
34 84
35 84 85
It should resemble coarse
G H I
breadcrumbs or a coarse
crumble texture. The
particles should be separate
Q R S
but if squeezed together it
should form a clump which
bonds together.
F G H
Switch the machine onto
H I J
speed 2-3.
Place some of the mix onto
I J
P Q R
the hopper. Feed a small
R S T
amount of mix into the
feed tube at a time. Allow
S T
Z
the scroll to clear before
J
continuing. If the feed tube
becomes clogged use the
end of the spanner/pusher
T
handle to push the mix
onto the scroll (do not use
anything other than the
spanner handle and do not
push too hard). Never let the
feed tube fill up.
G H I
When the pasta is long
enough, move the handle on
the cutting assembly back
Q R S
and forth to cut the pasta
into the desired length.
Alternatively if the cutting
assembly is not fitted use a
knife to cut the pasta.
To change dies remove the
l
cutting assembly by holding
the edge in one hand and
twist the clamp ring towards
you. Remove the securing
nut (use the spanner/pusher
to loosen the securing nut if
necessary) and switch briefly
to speed 1 to eject the die.
Remove the die and any
visible excess pasta and then
fit the desired die. Replace
the securing nut and cutting
assembly.
Warning
The pasta shaper will get
I I J J
–
hot in use – this is normal
and is caused by the pasta
being compressed in the
S S T T
attachment.
4
J
T
I J
S T
J
T
21/04/2022 10:58 21/04/2022 10:58